BenQ MX613ST, MS612ST user manual Adjusting the projected image, Adjusting the projection angle

Page 18

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the front

of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2. Screw the rear adjuster foot to fine-tune the

horizontal angle.	1				2



To retract the foot, hold up the projector while
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly lower
the projector. Screw the rear adjuster foot in a reverse		Do not look into the lens while
direction.		Do not look into the lens while
		the lamp is on. The strong light
If the projector is not placed on a flat surface or the		from the lamp may cause
screen and the projector are not perpendicular to		damage to your eyes.
each other, the projected image becomes trapezoidal.		Be careful when you press the
To correct this situation, see "Switching input signal"		quick-release button as it is
on page 24 for details.		close to the exhaust vent where
		hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press Auto on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

• The screen will be blank while Auto is functioning.

•This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.

Adjust the projected image to the size 2.

Sharpen the image by rotating the

that you need using the zoom ring.

focus ring.

18 Operation

Image 18

Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Important safety instructionsSafety Instructions Locations where the altitudes are higher Locations near fire alarmsLocations with an ambient temperature Confined. Allow at least 50 cm clearanceServiced InstalledIt from the power supplys power outlet Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Timer Set up Volume +Timer On FreezePull out the battery holder Remote control effective rangeReplacing the remote control battery Approx.+15ºFront Table Positioning your projectorChoosing a location Front CeilingScreen size Distance from screen mm Diagonal Projection dimensionsObtaining a preferred projected image size VerticalConnection Terminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorOperation Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Setting a password Using a security cable lockUtilizing the password function Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Projectors native resolution in its Displayed in the centerAdjustments Screen with a 169 aspect ratioSetting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes 3D Color Management Press To highlight Saturation and adjust itsEvery adjustment made will reflect to Range at 0, only pure red in the projectedCount Up Increases from 0 to the preset time Count Down Setting the presentation timerTo cancel the timer, perform the following steps Selection DescriptionFreezing the image Utilizing FAQ functionRemote paging operations Hiding the imageLocking control keys On the remote control or projector forTo activate the High Altitude Mode Operating in a high altitude environmentTurning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Muting the soundWireless connection Controlling the projector through a LAN environmentPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Save Settings Picture ModeTemperature Display menu Picture menu Function Description 3D SyncSettings System Setup Basic menu Function Description Quick AutoTimer SearchLock Panel KeyBackground SplashReset All System Setup Advanced menu Function DescriptionWireless Baud RateSystem Features ServiceCurrent StatusMaintenance Care of the projectorLamp information Setting Lamp Mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsCeiling Mount screw M4 x 8 Max L = 8 mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Timing Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs HorizontalCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement for European users Regulation statementsFCC statement for United States users Weee directive