BenQ MS612ST, MX613ST user manual Important safety instructions, Safety Instructions

Page 3

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1.Please read this manual before you operate your projector. Save it for future reference.

2.Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3.Refer servicing to qualified service personnel.

5.In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

6.Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press BLANK on the projector or remote control.

4.Always open the lens shutter (if any) or remove the lens cap (if any) when the projector lamp is on.

Important safety instructions

3

Image 3

Contents Welcome Table of contents Important safety instructions Important safety instructionsSafety Instructions Refer servicing to qualified service personnelSafety Instructions Confined. Allow at least 50 cm clearance Locations near fire alarmsLocations with an ambient temperature Locations where the altitudes are higherDo not step on the projector or place InstalledIt from the power supplys power outlet ServicedProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Freeze Volume +Timer On Timer Set upApprox.+15º Remote control effective rangeReplacing the remote control battery Pull out the battery holderFront Ceiling Positioning your projectorChoosing a location Front TableVertical Projection dimensionsObtaining a preferred projected image size Screen size Distance from screen mm DiagonalConnection Best Connecting video source devicesConnecting audio Terminal name Terminal appearanceOperation Starting up the projectorOperation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Highlight Change Security Settings and press MODE/ENTER Using a security cable lockUtilizing the password function Setting a passwordIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsScreen with a 169 aspect ratio Projectors native resolution in its Displayed in the centerAdjustments About the aspect ratioGo to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeFine-tuning the image quality in user modes Range at 0, only pure red in the projected Press To highlight Saturation and adjust itsEvery adjustment made will reflect to 3D Color ManagementSelection Description Setting the presentation timerTo cancel the timer, perform the following steps Count Up Increases from 0 to the preset time Count DownHiding the image Utilizing FAQ functionRemote paging operations Freezing the imageOperating in a high altitude environment On the remote control or projector forTo activate the High Altitude Mode Locking control keysMuting the sound Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneControlling the projector through a LAN environment Wireless connectionPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Display menu Picture menu Function Description 3D Sync Picture ModeTemperature Save SettingsSearch System Setup Basic menu Function Description Quick AutoTimer SettingsSplash Panel KeyBackground LockBaud Rate System Setup Advanced menu Function DescriptionWireless Reset AllStatus Features ServiceCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsUnit mm DimensionsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 Ceiling Mount screw M4 x 8 Max L = 8 mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Horizontal Supported timing for Component-YPbPrinputSupported timing for Video and S-Video inputs TimingDisclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement for United States users EEC statement for European users