BenQ MS612ST, MX613ST user manual Muting the sound, Adjusting the sound level

Page 33

1.Press CAPTURE on the remote control.

2.A confirmation message displays. Press CAPTURE or MODE/ENTER again.

3.The message 'Screen Capturing...' displays while the projector is processing the picture. Please wait.

4.If the action is successful, you see the message 'Captured Succeeded' on the screen. The captured picture is saved as My Screen.

5.To view the captured picture displayed as the startup screen, set My Screen in the

SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.

•Using the OSD menu

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Basic menu is highlighted.

2.Press to highlight MyScreen and press MODE/ENTER.

3.Repeat steps 2-5in the “Using the remote control” section to capture and view the

captured picture.

In the unlikely event that the capturing action fails, change your target picture.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker. Be sure you have made a correct connection to the projector audio input. See "Connection" on page 15 for how the audio input is connected.

Muting the sound

To temporarily turn off the sound:

1.Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted.

2.Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page displays.

3.Highlight Mute and press / to select On.

Adjusting the sound level

To adjust the sound level, press VOLUME+/VOLUME- on the remote control, or:

1.Repeat steps 1-2above.

2.Press to highlight Volume and press / to select a desired sound level.

Turning off the Power On/Off Ring Tone

To turn off the ring tone:

1.Repeat steps 1-2above.

2.Press to highlight Power On/Off Ring Tone and press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power On/Off Ring Tone.

Operation 33

Image 33

Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Timer On Volume +Timer Set up FreezeReplacing the remote control battery Remote control effective rangePull out the battery holder Approx.+15ºChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestOperation Starting up the projectorOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageTo activate the High Altitude Mode On the remote control or projector forLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Wireless connectionPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D SyncTimer System Setup Basic menu Function Description Quick AutoSettings SearchBackground Panel KeyLock SplashWireless System Setup Advanced menu Function DescriptionReset All Baud RateCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive