BenQ MS612ST, MX613ST user manual Magnifying and searching for details, Selecting the aspect ratio

Page 25

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

Using the remote control

1.Press Digital Zoom+/- to display the Zoom bar. Press Digital Zoom+ to magnify the center of the picture. Press the key repeatedly until the picture size is suitable for your need.

2.Use the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

3.To restore the picture to its original size, press Auto. You can also press Digital Zoom-. When the key is pressed again, the picture is further reduced until it is restored to the original size.

Using the OSD menu

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Digital Zoom and press MODE/ENTER. The Zoom bar displays.

3.Press repeatedly to magnify the picture to a desired size.

4.To navigate the picture, press MODE/ENTER to switch to the panning mode and press

the directional arrows ( , , , ) on the projector or remote control to navigate the picture.

5.To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out function, and press Auto to restore the picture to its original size. You can also press repeatedly until it is restored to the original size.

The picture can only be navigated after it is magnified. You can further magnify the picture while searching for details.

Selecting the aspect ratio

The “aspect ratio” is the ratio of the image width to the image height. Most analog TV and some computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected picture ratio (no matter what aspect the source is):

1.Press MENU/EXIT and then press / until the DISPLAY menu is highlighted.

2.Press to highlight Aspect Ratio.

3.Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

Operation 25

Image 25
Contents Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceIt from the power supplys power outlet InstalledServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Timer On Volume +Timer Set up FreezeReplacing the remote control battery Remote control effective rangePull out the battery holder Approx.+15ºChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsScreen size Distance from screen mm Diagonal VerticalConnection Connecting audio Connecting video source devicesTerminal name Terminal appearance BestStarting up the projector OperationOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTEREntering the password recall procedure If you forget the passwordWrite down the number and turn off your projector Disabling the password function Changing the passwordEnter a new password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAdjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratioSelecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projectedTo cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection DescriptionRemote paging operations Utilizing FAQ functionFreezing the image Hiding the imageTo activate the High Altitude Mode On the remote control or projector forLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a LAN environment Wireless connectionPage Page Page Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Description of each menu Temperature Picture ModeSave Settings Display menu Picture menu Function Description 3D SyncTimer System Setup Basic menu Function Description Quick AutoSettings SearchBackground Panel KeyLock SplashWireless System Setup Advanced menu Function DescriptionReset All Baud RateCurrent Features ServiceSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Connect the power and restart the projector MaintenanceResetting the lamp timer Light Status & Description Power events IndicatorsLamp events Thermal eventsTroubleshooting Projector specifications SpecificationsMm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25 DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mmSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming HorizontalLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement for United States users Regulation statementsEEC statement for European users Weee directive