BenQ MX613ST, MS612ST Using the menus, Following example describes how to set the OSD language

Page 20

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

Below is the overview of the OSD menu.

Main menu icon

Main menu

DISPLAY

Wall Color

Aspect Ratio

Keystone

Sub-menu

Position

Phase

H. Size

Digital Zoom

3D Sync

3D Sync Invert

Highlight

Teaching Template

Current input signal

Analog RGB

Off

Auto

ENTER

0

0

On

Disable

MENU Exit

Status

Press MENU/ EXIT to the previous page or to exit.

The following example describes how to set the OSD language.

1.Press MENU/EXIT on the projector or remote control to turn the OSD menu on.

DISPLAY

Wall Color	Off
Aspect Ratio	Auto
Keystone
Position
Phase	0
H. Size	0
Digital Zoom
3D Sync	On
3D Sync Invert	Disable
Teaching Template
Analog RGB	MENU Exit

3.Press to highlight Language

and press / to select a preferred language.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings	Front+Top
Remote Receiver	Front+Top
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
My Screen

Analog RGB

MENU Exit

2.Use / to highlight the SYSTEM SETUP: Basic menu.

SYSTEM SETUP: Basic

Presentation Timer
Language	English
Projector Position	Front Table
Menu Settings
Operation Settings	Front+Top
Remote Receiver	Front+Top
Panel Key Lock	Off
Background Color	BenQ
Splash Screen	BenQ
My Screen
Analog RGB	MENU Exit

4.Press MENU/EXIT twice* on the projector or remote control to leave and save the settings.

*The first press leads you back to the main menu and the second press closes the OSD menu.

20 Operation

Image 20

Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeIntroduction Projector featuresIntroduction Shipping contents Projector exterior view Projector Volume + Timer OnTimer Set up FreezeRemote control effective range Replacing the remote control batteryPull out the battery holder Approx.+15ºPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestOperation OperationStarting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusFollowing example describes how to set the OSD language Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERWrite down the number and turn off your projector If you forget the passwordEntering the password recall procedure Enter a new password Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageOn the remote control or projector for To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundWireless connection Controlling the projector through a LAN environmentPage Page Page Page Displaying images through Q Presenter Downloading and installing Q PresenterUsing Q Presenter Page Operation Presenting from a USB Reader Shutting down the projector Direct power offOnce the cooling process finishes, a Power Off Ring Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description 3D SyncSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key BackgroundLock SplashSystem Setup Advanced menu Function Description WirelessReset All Baud RateFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive