BenQ MX613ST Display menu Picture menu Function Description 3D Sync, Invert, Teaching, Template

Page 48

1. DISPLAY menu

2. PICTURE menu

Function

Description

3D Sync

When the 3D Sync function is On:

• The brightness level of the projected image will decrease.

(continued)

• The Picture Mode cannot be adjusted.

 

• The Keystone can only be adjusted within limited degrees.

3D Sync

When you discover the inversion of the image depth, enable this

Invert

function to correct the problem.

 

 

Teaching

Provides several preset patterns for various teaching purposes.

Choose Blackboard or Whiteboard first by pressing / and press

Template

/ to choose the pattern you need. Press MODE/ENTER to activate

 

the pattern.

 

 

Picture Mode

Pre-defined picture modes are provided so you can optimize your

projector image set-up to suit your program type. See "Selecting a

 

picture mode" on page 27 for details.

 

 

Reference

Selects a picture mode that best suits your need for the image quality

and further fine-tune the image based on the selections listed on the

Mode

same page below. See "Setting the User 1/User 2 mode" on page 27 for

 

details.

Brightness

Adjusts the brightness of the image. See "Adjusting Brightness" on page

28 for details.

 

 

 

Contrast

Adjusts the degree of difference between dark and light in the image.

See "Adjusting Contrast" on page 28 for details.

 

 

 

 

Adjusts the color saturation level -- the amount of each color in a video

Color

image. See "Adjusting Color" on page 28 for details.

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

 

Adjusts the red and green color tones of the image. See "Adjusting Tint"

Tint

on page 28 for details.

This function is only available when a Video or S-Video signal is

 

 

selected and the system format is NTSC.

 

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness

Sharpness" on page 28 for details.

This function is only available when a Video, S-Video or

 

 

Component Video signal is selected.

Brilliant Color

See "Adjusting Brilliant Color" on page 28 for details.

 

 

Color

There are four color temperature settings available. See "Selecting a

Temperature

color temperature" on page 28 for details.

 

 

3D Color

See "3D Color Management" on page 29 for details.

Management

 

 

 

Save Settings

Saves the settings made for User 1 or User 2 mode.

 

 

48 Operation

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Volume + Timer OnTimer Set up FreezeRemote control effective range Replacing the remote control batteryPull out the battery holder Approx.+15ºPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageOn the remote control or projector for To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundWireless connection Controlling the projector through a LAN environmentPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description 3D SyncSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key BackgroundLock SplashSystem Setup Advanced menu Function Description WirelessReset All Baud RateFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive
Top Page Image Contents