BenQ MX613ST, MS612ST user manual Switching input signal, Changing Color Space

Page 24

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. When starting up, the projector automatically searches for the available signals.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

To select the source:

•Using the remote control or projector

Press one of the Source buttons on the remote control, or press SOURCE on the projector repeatedly until your desired signal is selected.

•Using the OSD menu

1.Press SOURCE on the projector or remote control. A source selection bar displays.

2.Press / until your desired signal is selected and press MODE/ENTER.

Once detected, the selected source information will display at the corner of the screen for seconds. If there is multiple equipment connected to the projector, repeat steps 1-2to search for another signal.

Computer/YPbPr

HDMI

Video

S-Video

Network Display

USB Display

USB Reader

•The brightness level of the projected image will change accordingly when you switch between

different input signals. Data (graphic) "PC" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

•The native display resolution of this projector is in a 4:3 aspect ratio. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the “aspect ratio” setting, which may cause some image distortion or loss of picture clarity. See "Selecting the aspect ratio" on page 25 for details.

•Firewall in the PC must be switched off to allow Q Presenter and USB Display to work.

Changing Color Space

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.

To do this:

1.Press MENU/EXIT and then press / until the SOURCE menu is highlighted.

2.Press to highlight Color Space Conversion and press / to select a suitable color space.

This function is only available when the HDMI-input port is in use.

24 Operation

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Important safety instructionsSafety Instructions Locations near fire alarms Locations with an ambient temperatureLocations where the altitudes are higher Confined. Allow at least 50 cm clearanceInstalled It from the power supplys power outletServiced Do not step on the projector or placeProjector features IntroductionIntroduction Shipping contents Projector exterior view Projector Volume + Timer OnTimer Set up FreezeRemote control effective range Replacing the remote control batteryPull out the battery holder Approx.+15ºPositioning your projector Choosing a locationFront Table Front CeilingProjection dimensions Obtaining a preferred projected image sizeScreen size Distance from screen mm Diagonal VerticalConnection Connecting video source devices Connecting audioTerminal name Terminal appearance BestOperation Starting up the projectorOperation Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Using the menus Following example describes how to set the OSD languageUse / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Highlight Change Security Settings and press MODE/ENTERIf you forget the password Entering the password recall procedureWrite down the number and turn off your projector Changing the password Disabling the password functionEnter a new password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioProjectors native resolution in its Displayed in the center AdjustmentsAbout the aspect ratio Screen with a 169 aspect ratioUsing Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Press To highlight Saturation and adjust its Every adjustment made will reflect to3D Color Management Range at 0, only pure red in the projectedSetting the presentation timer To cancel the timer, perform the following stepsCount Up Increases from 0 to the preset time Count Down Selection DescriptionUtilizing FAQ function Remote paging operationsFreezing the image Hiding the imageOn the remote control or projector for To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound Adjusting the sound levelTurning off the Power On/Off Ring Tone Muting the soundWireless connection Controlling the projector through a LAN environmentPage Page Page Page Downloading and installing Q Presenter Using Q PresenterDisplaying images through Q Presenter Page Operation Presenting from a USB Reader Direct power off Once the cooling process finishes, a Power Off RingShutting down the projector Menu operation Menu systemMain menu Sub-menu Options Basic Advanced Description of each menu Picture Mode TemperatureSave Settings Display menu Picture menu Function Description 3D SyncSystem Setup Basic menu Function Description Quick Auto TimerSettings SearchPanel Key BackgroundLock SplashSystem Setup Advanced menu Function Description WirelessReset All Baud RateFeatures Service CurrentSystem StatusMaintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Status MessageReplacing the lamp Connect the power and restart the projector Maintenance Use the handle to slowly pull the lamp out ProjectorResetting the lamp timer Indicators Light Status & Description Power eventsLamp events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Mm W x 104.07 mm H x 244.11 mm D 311.81 51.1 58.25Ceiling Mount screw M4 x 8 Max L = 8 mm Unit mmTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputsTiming HorizontalWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statement for United States usersEEC statement for European users Weee directive
Top Page Image Contents