Ampro Corporation 5001451A manual Panel # Panel Class

Page 78

!Onboard Serial Ports — These items configure each serial port’s address and interrupt. Available choices for the I/O addresses are 3F8, 2F8, 3E8H, and 2E8H. Available IRQ choices for all four serial ports are IRQ3 and IRQ4. You also use IRQ10 and IRQ12 for serial ports 3 and 4, if these IRQs are not already assigned. If you select Auto, the BIOS automatically selects the IRQ for you. You may also disable any serial port.

!Onboard Parallel Port — This item sets the parallel port address and IRQ assignments. Available addresses are 378, 278, or 3BC. Available IRQ assignments are IRQ7 and IRQ5. You may also disable the port.

!Parallel Port Mode — This item sets the type of parallel port mode (ECP or ECP/EPP).

!ECP Mode Use DMA — This item selects a DMA channel to use with the ECP mode of the parallel port. This selection only applies if the parallel port is configured for ECP or ECP/EPP modes.

!Interface Select SerX — These items set the respective port for RS232 or RS485 compatibility.

!Onboard Sound Chip — This item enables or disables the on-board Audio subsystem.

!Onboard LAN Chip — This item enables or disables the on-board Ethernet controller.

!Assign IRQ for USB — This item allows you to manual select an IRQ for the USB port by setting this to Enable. If you set this to Disable, the IRQ for the USB port is automatically assigned.

!Onboard VGA Display — Choices are CRT, FP (Flat Panel), CRT/FP (CRT and Flat panel- display default setting), NTSC, and PAL.

Note

In CRT/FP mode the CRT may not display correctly depending on the

Flat Panel selected and the scan capabilities of the CRT monitor.

!VGA Flat Panel Type — There is support for 8 VGA Flat Panel Types, numbered 1 to 8. The list in Table 2-48 details the flat panel types available for each support number. For panel support not listed in Table 2-48, contact Ampro for more information.

Table 2-48. VGA Flat Panel Types

Panel #

 

Panel Class

 

 

1

1024x768 Dual Scan STN Color Panel

 

 

2

1280x1024 TFT Color Panel

 

 

 

3

640x480

Dual Scan STN Color Panel

 

 

 

4

800x600

Dual Scan STN Color Panel

 

 

 

5

640x480

Sharp TFT Color Panel

 

 

 

6

640x480

18-bit TFT Color Panel

 

 

7

1024x768 TFT Color Panel

 

 

 

8

800x600

TFT Color Panel

 

 

 

2-60

Image 78
Contents Little Board P6d Reference Manual Revision Reason for Change Date Copyright 2000, 2002, Ampro Computers, IncorporatedTable of Contents Preface ROM Bios Standards Contact Information Cables Index Page Website IntroductionTechnical Support Surface MailViii Product Feature Summary General DescriptionCPU/Motherboard Enhanced Embedded-PC Bios Modular PC/104-Plus Expansion BusCompactFlash Disk Floppy Interface Serial PortsParallel Port PCI-Bus Eide InterfacesFlat Panel/CRT Display Controller MBps Ethernet LAN InterfaceEnhanced Reliability SoftwareDesigning Little Board Systems On-board MiniModule ExpansionLittle Board Development Platform And QuickStart Kit I/O Development BoardConnector Name Description Connector DescriptionsJ2 Power Pin # SignalJ4 Keyboard Switch Descriptions S1 S5J3 Misc J5 MouseSystem Block Diagram Page Mounting Dimensions OverviewLittle Board P6d Module with Mounting Dimensions Connector Summary Connector Function Size Key PinPage Little Board P6d Connector and Jumper Locations Jumper Group Function Default Jumper SummaryPin # Signal Name Function DC PowerPower Requirements Connector Type Mating ConnectorBackup Battery Switching Power SuppliesPowerfail NMI Cooling RequirementsFan Connector System MemoryPin # Function Bios Recovery Interrupt and DMA Channel UsageShadowing Interrupt Function Battery-Backed Clock Serial PortsChannel Function Addresses and Interrupt Assignments ROM-BIOS Installation of the Serial PortsSerial Port Connectors J8, J11 Port Address InterruptPorts Pin # Signal Name Function In/Out DB25 Pin DB9 Pin Signal DB25Ports Pin # Name Function Serial TTL Option Ampro Custom Serial FeaturesSerial Console Features Jumper ResultUsing a Standard PC Keyboard COM Port Table Using Arrow Keys During SetupUniversal Serial Bus USB Ports Function Substitute KeysJ5 Pin # Signal Name Function IrDA Connector Part of Utility J19J4 Pin # Signal Name Function Infrared IrDA InterfaceMulti-Mode Parallel Port ROM-BIOS Installation of Parallel PortsJ19 Pin # Signal Name Function Addresses and InterruptsParallel Port Connector J9 DMA ChannelsPin # Signal Name Function In/Out DB25 Pin IEEE-1284-compliant CablesParallel Port Registers Using the Parallel Port in Bidirectional ModeLatch-Up Protection Standard and Bidirectional OperationUsing the Control Lines for Additional I/O Enabling the Parallel Port Interrupt22. Parallel Port Register Bits Floppy Drive Considerations Floppy Interface ConfigurationFloppy Disk Interface Capacity Drive Size Tracks Data RateFloppy Interface Connector J14 Pin # Signal Name Function In/OutEide Hard Disk Interface Pin # Signal Function Name CompactFlash Solid-State Disk IDE Interface ConfigurationMaster/Slave Setting Enabling the DriveAudio Interface Connector Audio InterfaceAudio Amplifier Connector Function Type Signals Audio Interface Adapter Schematic Pin # Signal Function Flat Panel/CRT Video ControllerConnecting a Flat Panel J15 Name Connector Pins/Type DescriptionPower Sequencing Advanced Power ManagementBios Support of Standard Flat Panels Connecting a CRT J17Pin # Signal Name DB-15 ZV Port Interface J16J6 Pin # Name Function Disabling the Video Controller Ethernet RJ45 Interface Connector J13Ethernet Network Interface Hardware DescriptionNetwork Operating Systems Ethernet Interface SoftwareManufacturers Ethernet ID Network OS DriversEthernet Indicator LEDs Watchdog TimerEthernet Setup Color Designation FunctionUtility Connectors J19 38. Utility Connector J19 Speaker Connections Push-button Reset ConnectionLED Connection Keyboard ConnectionIrDA Interface Miscellaneous Power Management SignalsPC/104-Plus Expansion Bus TTL Serial PortsUsing Standard PC and AT Bus Cards Expansion Bus Connector PinoutsPin # Signal Name Function Pin # Signal Function Name Pin 12VSetup Setup HelpMenu Name Functions Setup 1 Main Menu ↑ ↓ → ←Setup 2 Standard Cmos Setup Eide Hard Disk DrivesDrive Selection Setup 3 Bios Features Setup VideoSerial Console Operation during Setup Setup 4 Chipset Features Setup 10. Setup 4 Chipset Features SetupSetup 5 Power Management Setup 11. Setup 5 Power Management SetupPage Setup 6 PCI Configuration Setup 12. Setup 6 PCI Configuration SetupSetup 7 Integrated Peripherals Setup Integrated Peripherals SetupPanel # Panel Class Other Setup Screens Load Setup Defaults ScreenIDE HDD Auto Detection Screen Save & Exit Setup Screen Exit Without Saving ScreenLittle Board P6d Technical Specifications Embedded-PC System EnhancementsOn-board Peripherals Mechanical and Environmental Specifications Support SoftwareBios Modes Flat Panel DisplaysSupported CRT Video Modes-Standard VGA Supported CRT Video Modes-Low Resolution Supported CRT Video Modes-Extended Modes 46h Generic 32K 8x16 Hardware IRQ Map IRQ #Page Appendix a Standards Contact Information EPP and ECP OperationPage Appendix B Cables Page Cable Setup Index Setup summary Shadowing Index Index-4