3M X75 manual Option Menu, ONE Touch Auto Search Auto OFF

Page 38

Multifunctional settings

OPTION Menu

With the OPTION menu, items shown in the table below can be performed.

Select an item using the cursor buttons ▲/▼ on the projector or remote control, and press the cursor button ► on the projector or remote control, or the ENTER button on the remote control to progress, except for the items LAMP TIME and FILTER TIME. Then perform it referring to the following table.

 MENU [RGB]

   :SELECT

 PICTURE

 ONETOUCH

 IMAGE

 AUTO SEARCH  TURN OFF

 VIDEO Qlty.  AUTO OFF      0

 INPUT

 LAMP TIME     0

 SETUP

 FILTER TIME   0

 SCREEN

 SERVICE

 OPTION

 NETWORK

 

 EASY MENU

 

Item

ONE TOUCH

AUTO SEARCH

AUTO OFF

Description

Using the buttons ▲/▼ turns on/off the automatic keystone correction function.

TURN ON TURN OFF

You can automatically correct vertical keystone distortion corresponding to the angle (forward/backward tilt) at which the unit is set up. This function works with ONE TOUCH operation.

If the projection screen is inclined, or if the projector is angled downwards, it may not be possible to make the correct adjustment when V: INVERT or H&V: INVERT is selected under the MIRROR item of the SETUP menu.

When the zoom adjustment is set to the TELE side, automatic correction may be excessive. The automatic correction function should be used with zoom set to WIDE whenever possible.

Using the buttons ▲/▼ turns on/off the automatic signal search function.

TURN ON TURN OFF

This function works with INPUT, RGB, and VIDEO buttons. When the TURN ON is selected, detecting no signal automatically cycles through input ports in order of following. The search is started from the current port. Then when an input is found, the projector will stop searching and display the image.

RGB IN1 RGB IN2 DVI-D COMPONENT VIDEO S-VIDEO VIDEO

Using the buttons ▲/▼ adjusts the time to count down to automatically turn the projector off.

Long (max. 99 minutes) Short (min. 0 minute = DISABLE)

AUTO OFF

AUTO OFF

ENABLE

DISABLE

1

0

When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with

a no-signal or an unsuitable signal reaches at the set time, the projector lamp will go off and the power indicator begins blinking. Please refer to the section “Turning off the power” (16).

38

Image 38
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents About contents of package DVI-D port  Part namesProjector RGB IN2 port Control buttons Remote controlLaser Indicator 14 STANDBY/ONSetting up Fastening the lens capAt 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Video out Connecting power supply Putting batteries Remote controlLaser pointer Using the remote control Turning off the power Power on/offTurning on the power STANDBY/ONOperating Adjusting the volumeSelecting an input signal Temporarily muting the soundPress the ONE Touch button on the remote control. This Adjusting screen with ONE-TOUCHAdjusting the zoom and focus Selecting an aspect ratio At a video signal Using the automatic adjustment featureAdjusting the position Using the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen At the Easy Menu Multifunctional settingsUsing the menu function At the advanced MenuDescription Aspect Mode Bright Contrast Color Tint Shrpness WhisperEasy Menu Go To Advanced Menu Description Mirror Reset Filter Time LanguageEasy Menu NetworkGamma #3 Custom  #3 Default  #2 CustomPicture Menu High  Middle  LOW  Custom Picture MenuColor Temp Color Tint SharpnessMY Memory LOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1At a video signal / no signal 43  169  Small Aspect Over Scan Position PhaseAt a RGB/DVI signal Image MenuAt a video signal Size Auto Adjust ExecuteAt a RGB signal Image MenuTV  Film  Turn OFF Video Qlty. MenuProgressive 3D-YCS Video NR Still Image  Normal  Turn OFFComponent  Scart RGB Input MenuColor Space Component Video Format DVI Auto  Ntsc  PAL  SecamInput Menu InformationNormal  Whisper Setup MenuWhisper Mirror Volume Stereo IR Remote Normal  Hinvert  Vinvert  H&VINVERTBright  Dark Screen MenuMenu Position OSD Bright Blank My Screen My Screen Lock Description Screen MenuStart UP Turn on  Turn OFFMessage No Input is Detected Sync is OUT of RangeOption Menu ONE Touch Auto Search Auto OFFOption Menu Lamp Time Filter Time ServiceFactory Reset FAN SpeedDhcp IP Address Subnet Mask Default GatewayNetwork Menu Ex. Case of IP Address = When your network enables the Dhcp functionNetwork Menu Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Inside of the projector Caring for the cabinet and remote controlOther care Caring for the lensRelated messages Time the lamp timer has counted is approaching 2000 hoursThere is no input signal Internal portion temperature is rising Related messagesRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsIt is time to clean the ai r filter There is a possibility that the interior portionPhenomena that may easily be mistaken for machine defects Electrical power cord is not pluggedPower switch is not set to the on position Phenomena that may easily be mistaken for machine defects RGB input SpecificationDigital RGB input RGB outputSpecifications Not included with Basic Packet Part Number Accessories Part NumberHow to Order DN00801-X75OGENG

X75 specifications

The 3M X75 is a versatile and innovative product designed to meet the demands of various industries. Known for its excellent performance, the X75 incorporates advanced technologies that provide users with superior capabilities. This article delves into its main features, technologies, and characteristics that set it apart in the marketplace.

One of the standout features of the 3M X75 is its exceptional adhesion properties. It uses a unique adhesive formulation that ensures a strong bond to a variety of surfaces. This makes it an ideal choice for applications where reliability is critical. Whether in automotive, construction, or other sectors, the X75 offers a performance that professionals can depend on.

Another key characteristic of the 3M X75 is its durability. The product is engineered to withstand harsh environmental conditions, including extreme temperatures, moisture, and UV exposure. This resilience makes it suitable for both indoor and outdoor applications, ensuring that it maintains its integrity over time.

Additionally, the technology behind the 3M X75 includes a pressure-sensitive adhesive that provides immediate bond strength upon application. This allows users to work efficiently without waiting for curing times, which can slow down workflows. The quick application process is complemented by the product's easy handling, making it user-friendly for various projects.

The design of the 3M X75 also emphasizes flexibility. It can be adapted for different applications, ranging from automotive parts to signage and displays. Its ability to conform to uneven surfaces expands its usability, making it a go-to solution for a plethora of projects.

Another notable feature is its clean removal capability. The 3M X75 is designed to peel away cleanly from surfaces without leaving any residue behind, which is crucial for anyone looking to maintain a neat working environment.

In summary, the 3M X75 stands out due to its superior adhesion, durability, pressure-sensitive technology, flexibility, and clean removal attributes. These characteristics make it a reliable and versatile choice for professionals across various industries, enhancing productivity and ensuring high-quality results for any application.