3M X75 manual Maintenance, Lamp

Page 44

Maintenance

Maintenance

Lamp

WARNING

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►The projector uses a high-pressure mercury glass lamp. The lamp can break

with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. In addition, when the bulb bursts, it is possible for shards of glass to fl y into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

►About disposal of a lamp • This product contains a mercury lamp; do not

put in trash. Dispose of in accord with environmental laws. For lamp recycling, go to www.lamprecycle.org. (in the US)

For product disposal, contact your local government agency or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

Disconnect

the plug from the

power

outlet

•If the lamp should break (it will make a loud bang when it does), unplug the power cord from the outlet, and make sure to request a replacement lamp from your local dealer. Note that shards of glass could damage the projector’s internals, or cause injury during handling, so please do not try to clean the projector or replace the lamp yourself.

•If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

•Before replacing the lamp, turn the projector off and unplug the power cord, then wait at least 45 minutes for the lamp to cool sufficiently. Handling the lamp while hot can cause burns, as well as damaging the lamp.

•Never unscrew except the appointed (marked by an arrow) screws.

•Do not open the lamp door while the projector is suspended from above. This is dangerous, since if the lamp’s bulb has broken, the shards will fall out when the cover is opened. In addition, working in high places is dangerous, so ask your local dealer to have the lamp replaced even if the bulb is not broken.

•Do not use the projector with the lamp door removed. At the lamp replacing, make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•Use only the lamp of the specifi ed type.

•If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems elsewhere besides the lamp. If this happens, contact your local dealer or a service representative.

•Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

•If the indicators or a message prompts you to replace the lamp (see the section "Related Messages" and "Regarding the indicator Lamps"), replace the lamp as soon as possible. Using the lamp for long periods of time, or past the replacement date, could cause it to burst. Do not use old (used) lamps; this is a cause of breakage.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Trademark acknowledgment About this manualThank you for purchasing this projector Contents About contents of package Part names ProjectorDVI-D port  RGB IN2 port Remote control Laser Indicator 14Control buttons STANDBY/ONSetting up Fastening the lens capAt 169 screen ArrangementAt 43 screen Adjusting the projectors elevator About the filter cover for bottom-up use Connecting your devices About Plug-and-Play capabilityExamples of connection with a computer Connecting to a monitor outputConnecting to a speaker with amplifier output Video out Connecting power supply Putting batteries Remote controlLaser pointer Using the remote control Power on/off Turning on the powerTurning off the power STANDBY/ONAdjusting the volume Selecting an input signalOperating Temporarily muting the soundAdjusting screen with ONE-TOUCH Adjusting the zoom and focusPress the ONE Touch button on the remote control. This Selecting an aspect ratio At a video signal Using the automatic adjustment featureAdjusting the position Using the magnify feature Correcting the keystone distortionsFreezing the screen Temporarily blanking the screenUSB mouse and keyboard control Available function Remote control operationOperating the computer screen Multifunctional settings Using the menu functionAt the Easy Menu At the advanced MenuDescription Aspect Mode Bright Contrast Color Tint Shrpness WhisperEasy Menu Mirror Reset Filter Time Language Easy MenuGo To Advanced Menu Description NetworkGamma #3 Custom  #3 Default  #2 CustomPicture Menu Picture Menu Color TempHigh  Middle  LOW  Custom Color Tint SharpnessMY Memory LOAD1  LOAD2  LOAD3  LOAD4 SAVE4 SAVE3  SAVE2  SAVE1Aspect Over Scan Position Phase At a RGB/DVI signalAt a video signal / no signal 43  169  Small Image MenuSize Auto Adjust Execute At a RGB signalAt a video signal Image MenuVideo Qlty. Menu Progressive 3D-YCS Video NRTV  Film  Turn OFF Still Image  Normal  Turn OFFInput Menu Color Space Component Video Format DVIComponent  Scart RGB Auto  Ntsc  PAL  SecamInput Menu InformationSetup Menu Whisper Mirror Volume Stereo IR RemoteNormal  Whisper Normal  Hinvert  Vinvert  H&VINVERTBright  Dark Screen MenuMenu Position OSD Bright Blank Screen Menu Start UPMy Screen My Screen Lock Description Turn on  Turn OFFMessage No Input is Detected Sync is OUT of RangeOption Menu ONE Touch Auto Search Auto OFFLamp Time Filter Time Service Factory ResetOption Menu FAN SpeedDhcp IP Address Subnet Mask Default GatewayNetwork Menu Ex. Case of IP Address = When your network enables the Dhcp functionNetwork Menu Screen Network Menu Maintenance LampCase of replacement by yourself LampAir filter Caring for the cabinet and remote control Other careInside of the projector Caring for the lensRelated messages Time the lamp timer has counted is approaching 2000 hoursThere is no input signal Internal portion temperature is rising Related messagesRegarding the indicator lamps Regarding the indicator lamps It is time to clean the ai r filterCooling fan is not operating There is a possibility that the interior portionPhenomena that may easily be mistaken for machine defects Electrical power cord is not pluggedPower switch is not set to the on position Phenomena that may easily be mistaken for machine defects Specification Digital RGB inputRGB input RGB outputSpecifications Not included with Basic Packet Part Number Accessories Part NumberHow to Order DN00801-X75OGENG

X75 specifications

The 3M X75 is a versatile and innovative product designed to meet the demands of various industries. Known for its excellent performance, the X75 incorporates advanced technologies that provide users with superior capabilities. This article delves into its main features, technologies, and characteristics that set it apart in the marketplace.

One of the standout features of the 3M X75 is its exceptional adhesion properties. It uses a unique adhesive formulation that ensures a strong bond to a variety of surfaces. This makes it an ideal choice for applications where reliability is critical. Whether in automotive, construction, or other sectors, the X75 offers a performance that professionals can depend on.

Another key characteristic of the 3M X75 is its durability. The product is engineered to withstand harsh environmental conditions, including extreme temperatures, moisture, and UV exposure. This resilience makes it suitable for both indoor and outdoor applications, ensuring that it maintains its integrity over time.

Additionally, the technology behind the 3M X75 includes a pressure-sensitive adhesive that provides immediate bond strength upon application. This allows users to work efficiently without waiting for curing times, which can slow down workflows. The quick application process is complemented by the product's easy handling, making it user-friendly for various projects.

The design of the 3M X75 also emphasizes flexibility. It can be adapted for different applications, ranging from automotive parts to signage and displays. Its ability to conform to uneven surfaces expands its usability, making it a go-to solution for a plethora of projects.

Another notable feature is its clean removal capability. The 3M X75 is designed to peel away cleanly from surfaces without leaving any residue behind, which is crucial for anyone looking to maintain a neat working environment.

In summary, the 3M X75 stands out due to its superior adhesion, durability, pressure-sensitive technology, flexibility, and clean removal attributes. These characteristics make it a reliable and versatile choice for professionals across various industries, enhancing productivity and ensuring high-quality results for any application.
Top Page Image Contents