LG Electronics BX220-JD owner manual Safety Instructions

Page 4

Safety Instructions

Safety Instructions

Please take note of the safety instructions to prevent any potential accident or misuse of the projector.

Safety Instructions are given in two forms as detailed below.

WARNING : The violation of this instruction may cause serious injuries and even death.

NOTES : The violation of this instruction may cause light injuries or damage to the projector.

After reading this manual, keep it in the place that the user always can contact easily.

Indoor Installation

Do not place the Projector in direct sunlight or near heat sources such as radiators, fires and stove etc.

This may cause a fire hazard !

WARNING

Do not place inflammable materi-

Do not allow children to hang on

als beside the projector

the installed projector.

This may cause a fire hazard !

It may cause the projector to fall, caus-

ing injury or death.

 

 

Indoor Installation

NOTES

 

 

 

Disconnect from the mains and remove all connections before moving.

Do not place the projector close to sources of steam or oil such as a humidifier.

This may create a fire hazard or an electric shock hazard !

Do not place the projector where it might be exposed to dust.

This may cause a fire hazard !

When installing the projector on a table, be careful not to place it near the edge.

This may cause the projector to fall causing serious injury to a child or adult and serious damage to the projector.

Only use a suitable stand.

Do not block the vents of the pro- jector or restrict air-flow in any way.

This would cause the internal tempera- ture to increase and could cause a fire hazard!

Only use the projector on a level

Ensure good ventilation around the

and stable surface.

projector. The distance between

It may become unstable and affect

the projector and the wall should

be more than 20cm/8 inches.

operation.

 

 

An excessive increase in its inter-

 

nal temperature may cause a fire

 

hazard!

Do not place the projector directly on a carpet, rug or place where ventilation is restricted.

This would cause its internal temperature to increase and might create a fire hazard !

 

Outdoor Installation

WARNING

 

 

 

Do not use the projector in a damp place such as a bathroom where it is likely to get wet.

This may cause a fire or an electric shock hazard !

 

Power

WARNING

 

 

 

Earth wire should be connected.

If the earth wire is not connected, there is a possible danger of electric shock caused by the current leakage.

If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.

Do not connect ground to telephone wires, lightning rods or gas pipe.

The mains plug should be insert- ed fully into the power outlet to avoid a fire hazard !

This may cause a fire hazard !

Do not place heavy objects on the power cord

This may cause a fire or an electric shock hazard !

4

Image 4
Contents BX220-JD DLP Projector Class a digital deviceContents Safety Instructions Never touch the power plug with a wet hand Prevent dust collecting on the power plug pins or outletDo not use too many plugs on the Mains multi-outlet Do not allow any objects to fall into the projectorDo not use water while cleaning the projector Is not to be used for a long peri Service personnelOnly use the specified type of battery Do not drop the projector or allow impact shockNames of parts Connecting PartMain Body Control Panel Remote Control Installing BatteriesProjector Status Indicators Accessories Optional ExtrasInstallation and Composition Installation InstructionsDon’t place the projector where it can be covered with dust Provide proper ventilation for this projectorBasic Operation of the Projector Projection distance based on the picture formatUsing Kensington Security System Turning on the Projector Turning off the ProjectorSelecting source mode Focus and Position of the Screen ImageZoom ring Focus ring Each press of the F, G button changes the display as belowConnecting to a Desktop PC Connecting to a Notebook PCConnection Connect computer cable to RGB Input PC/DTV of the projectorConnecting to a Video Source Connecting to a DVDConnecting to a D-TV Set-Top Box RGB Input PC/DTV of the projectorAdjusting Video FunctionAPC Auto Picture Control FunctionWhite Peaking Function Auto Color Temperature ControlGamma Function Flip Horizontal Function Selecting languageFlip Vertical Function Using Keystone function Using ARC FunctionAuto Source Function Lamp Mode Function Using Blank functionSelecting Blank Image color Checking lamp time Using Still functionMoving Image Still Image Auto Tracking Function Clock / Phase FunctionScreen Position Communication Parameter Setup How to connect external control equipmentRS-232C Command Reference List Communication ProtocolPower Command2a Input Select Command2bAspect Ratio Command2c Screen Mute Command2dBrightness Command2h Color Command2iTint Command2j Sharpness Command2kRed ADC gain Adjustment Color R Command2w Low Power Command2qGreen ADC gain Adjustment Color G Command2y Blue ADC gain Adjustment Color B Command2zInformation Supported Monitor DisplayDVD/DTV Input Maintenance Cleaning the lensMemo Memo Specifications BX220-JDOperating Condition Projector Lamp