Polaroid Polaview 220 manual Using the remote control

Page 24

Using the projector 21

Standby mode

Use the Standby mode to prolong the life of the projector

 

lamp. When you select the Standby mode by pressing the

 

LAMP key, the green LED power indicator on the rear panel

 

of the projector begins to blink and continues to do so for

 

3 minutes, to allow the projector to cool down. The projec-

 

tor must complete this 3-minute cool-down period before it

 

can resume normal operation. The green LED resumes its

 

normal steady glow at the end of 3 minutes. Press the

 

LAMP key again to resume operation of the projector.

 

Warning: The projector lamp should always be turned on

 

for a minimum of 3 minutes and allowed to cool for at least

 

3 minutes before you turn it back on again. Failure to follow

 

these precautions can lead to premature lamp degradation

 

and, on rare occurrences, lamp rupture. Do not operate the

 

lamp past the rated lamp life. Excessive operation of the

 

lamp past its rated life can cause them to fracture or burst.

Using the remote control

The remote control contains all the key functions available on the projector control panel as well as several additional features. For the projector to receive signals from the remote control, point the remote control directly at the infrared sensor on top of the projector. You can also deflect the remote-control signal off the projection screen. When used with the computer IR (infrared) receiver kit, the remote- control cursor pad controls the movement of your computer cursor. The remote control also has a low-powered laser for use as a pointing device during presentations.

Note: For setup procedures for the computer IR (infrared) receiver, refer to the separate instruction manual included in your computer IR receiver kit (part number SB06).

Caution: Take care not to point the remote-control laser- light beam toward your audience. The light beam could cause eye injury.

Image 24
Contents Polaview Radiate radio frequency energy and, if not installed Protection against such interference when operated in aRegarding safety, public health, environment Specifications are subject to change without noticeTable of contents Storage, cleaning and care Replacing the lamp Appendix a Parts Appendix B StandardsIntroduction What’s in the box? Items included with the projectorComputer/video compatibility Connector panel Quick startIntroduction Introduction Detailed setup Polaroid Polaview Model 220 Projector and remote controlYour Polaview Model 220 Projector Polaroid Polaview Model 220 Projector rear view Getting started Connector panel Computer Inputs Outputs Stereo L R Redrive RSComputer and VCR connections To Mac into the computer monitor port. Plug the end Labeled To VGA into the projector MAC/PC port seeInput composite jacks yellow on the projector connector Connect one of the yellow RCA composite video cableVideo source. Connect the yellow plug at the other end Panel see the illustration belowUse Sources 1 and 2 to connect Supplying power to the projector Power receptacle and AC power switchUsing the projector Turning on the projectorOn the control panel or remote control. Adjust the image Size by using the Zoom control on the control panel orWant to adjust the rear feet of the projector to position Focus the projected image with the Focus control eitherControl-panel keys Image, when used with the cursor Decreases or increases the volumeAdjusts the focus of the image Adjusts the brightness and contrastUsing the remote control Controls the volume, balance, treble Brightness, contrast, tint, phaseLaser pointer Serves as a pointing device Bass of the source connected toFocus + Adjusts the focus of the image Zoom + Zooms in and out. Press + to makeMenu selections Select the Setup menu to make adjustments to Following settingsOr rear projection mode Resets all adjustments toImage optimization From the projector control panel or remote control, press Using the cursor pad, scroll through the menu selectionsAdjust brightness and contrast. The correct combination Examine the projected image for horizontal noise bars orUse the Tint option to make the adjustments Adjust the color balance of the projected imageChanges from the default setting are stored in memory for Control panel or remote control commands, you canMaintenance Storage, cleaning and careReplacing the lamp assembly Unlock the lamp assembly by rotating the locking key on Half revolution. Grasp the wire handle and gently pullLamp assembly straight out of the unit Align the lamp-assembly slide rails with the slide-railTroubleshooting Troubleshooting guideSymptom Cause Solution Where to get help Your computer dealerIf at any time you need help Polaroid Offices and Service Centers BrasilNew Zealand One Year Warranty Maintenance Replacement product Optional accessoryAppendix a Parts OG45Appendix a Appendix B Standards