Polaroid Polaview 220 manual Introduction

Page 9

Introduction 5

4To supply power to the projector, connect the power cable to the power port on the rear panel of the projector. Then connect the power cord to an appropriate power outlet. Turn on the power switch located on the rear panel of the projector, beside the power port. After approximately 30 seconds after the power is on, a solid-colored image is pro- jected onto your screen.

Note: You may detect a high-pitched sound as the color- wheel and fans are reaching operating speed. Also, as you turn on the projector, you may detect a slight, crackling, electrostatic sound as the bulb illuminates. It may take up to 10 seconds for the bulb to reach full brightness.

A keystone correction of 17 degrees is built into the projec- tor to compensate for image distortion. You may want to adjust the rear feet of the projector to position the image on the screen.

5Turn on your computer or video source. Select the desired source for display by pressing the appropriate SOURCES button on the projector control panel or remote control. Your computer or video image then appears on the projec- tion screen. The selected SOURCES button is backlit green; all other SOURCES buttons are backlit red.

Note: For information about the operation of your external computer or video sources, refer to the appropriate instruc- tion manual for the equipment in question.

6Focus the projected image with the FOCUS control either on the control panel or remote control. Adjust the image size by using the ZOOM control on the control panel or remote control. Use the projector SETUP and IMAGE menus to adjust the settings to fine-tune your projected image. (For more detailed instructions for image adjustments, see Chapter 4, Using the projector.

Image 9

Contents Polaview Protection against such interference when operated in a Radiate radio frequency energy and, if not installedRegarding safety, public health, environment Specifications are subject to change without noticeTable of contents Appendix a Parts Appendix B Standards Storage, cleaning and care Replacing the lampIntroduction Items included with the projector What’s in the box?Computer/video compatibility Quick start Connector panelIntroduction Introduction Detailed setup Polaroid Polaview Model 220 Projector and remote controlYour Polaview Model 220 Projector Polaroid Polaview Model 220 Projector rear view Getting started Computer Inputs Outputs Stereo L R Redrive RS Connector panelComputer and VCR connections Labeled To VGA into the projector MAC/PC port see To Mac into the computer monitor port. Plug the endConnect one of the yellow RCA composite video cable Input composite jacks yellow on the projector connectorVideo source. Connect the yellow plug at the other end Panel see the illustration belowUse Sources 1 and 2 to connect Power receptacle and AC power switch Supplying power to the projectorTurning on the projector Using the projectorSize by using the Zoom control on the control panel or On the control panel or remote control. Adjust the imageWant to adjust the rear feet of the projector to position Focus the projected image with the Focus control eitherControl-panel keys Decreases or increases the volume Image, when used with the cursorAdjusts the focus of the image Adjusts the brightness and contrastUsing the remote control Brightness, contrast, tint, phase Controls the volume, balance, trebleLaser pointer Serves as a pointing device Bass of the source connected toZoom + Zooms in and out. Press + to make Focus + Adjusts the focus of the imageMenu selections Following settings Select the Setup menu to make adjustments toOr rear projection mode Resets all adjustments toImage optimization Using the cursor pad, scroll through the menu selections From the projector control panel or remote control, pressAdjust brightness and contrast. The correct combination Examine the projected image for horizontal noise bars orAdjust the color balance of the projected image Use the Tint option to make the adjustmentsChanges from the default setting are stored in memory for Control panel or remote control commands, you canStorage, cleaning and care MaintenanceReplacing the lamp assembly Half revolution. Grasp the wire handle and gently pull Unlock the lamp assembly by rotating the locking key onLamp assembly straight out of the unit Align the lamp-assembly slide rails with the slide-railTroubleshooting Troubleshooting guideSymptom Cause Solution Where to get help Your computer dealerIf at any time you need help Brasil Polaroid Offices and Service CentersNew Zealand One Year Warranty Maintenance Optional accessory Replacement productAppendix a Parts OG45Appendix a Appendix B Standards