Polaroid Polaview 220 manual Connect one of the yellow RCA composite video cable

Page 17

Detailed setup 13

NTSC/PAL/SECAM

Place the projector on a tabletop or other level surface

video connections

with the lens facing the projection screen.

 

1 Connect one of the yellow RCA composite video cable

 

(part number CA19) plugs into the VIDEO OUT jack of your

 

video source. Connect the yellow plug at the other end of

 

the cable to either of the SOURCE 1 or SOURCE 2 video-

 

input composite jacks (yellow) on the projector connector

 

panel (see the illustration below).

Composite video

 

 

 

 

 

 

connections

 

 

 

VCR or laser disk player

AUDIO VIDEO S-VIDEO

L R

Yellow

Red

White

White

 

 

SOURCE 1

Red

 

 

SOURCE 2

Yellow

 

 

 

 

 

SOURCE 1

SOURCE 2

SOURCE 3

SOURCE 4

OUTPUTS

L R

L R

STEREO

STEREO

STEREO L

R

 

 

MAC / PC

PC / MAC

REDRIVE

RS 232

VIDEO INPUTS

COMPUTER INPUTS

 

 

Use SOURCES 1 and 2 to connect more than one audio/video device (one cable per device)

Audio/Video cable

The projector is also compatible with S-video sources

(for the appropriate connections, refer to the illustration on the next page).

Note: You must connect audio and video sources to the same source channel if you plan to select them simultane- ously.

2Connect the red RCA audio-video cable plug to the AUDIO R (right) jack of your audio source. Then connect the red plug at the projector end of the cable to a red audio jack (either SOURCE 1 or SOURCE 2 R) on the projector connector panel.

Image 17
Contents Polaview Protection against such interference when operated in a Radiate radio frequency energy and, if not installedRegarding safety, public health, environment Specifications are subject to change without noticeTable of contents Appendix a Parts Appendix B Standards Storage, cleaning and care Replacing the lampIntroduction Items included with the projector What’s in the box?Computer/video compatibility Quick start Connector panelIntroduction Introduction Your Polaview Model 220 Projector Detailed setupPolaroid Polaview Model 220 Projector and remote control Polaroid Polaview Model 220 Projector rear view Getting started Computer Inputs Outputs Stereo L R Redrive RS Connector panelComputer and VCR connections Labeled To VGA into the projector MAC/PC port see To Mac into the computer monitor port. Plug the endConnect one of the yellow RCA composite video cable Input composite jacks yellow on the projector connectorVideo source. Connect the yellow plug at the other end Panel see the illustration belowUse Sources 1 and 2 to connect Power receptacle and AC power switch Supplying power to the projectorTurning on the projector Using the projectorSize by using the Zoom control on the control panel or On the control panel or remote control. Adjust the imageWant to adjust the rear feet of the projector to position Focus the projected image with the Focus control eitherControl-panel keys Decreases or increases the volume Image, when used with the cursorAdjusts the focus of the image Adjusts the brightness and contrastUsing the remote control Brightness, contrast, tint, phase Controls the volume, balance, trebleLaser pointer Serves as a pointing device Bass of the source connected toZoom + Zooms in and out. Press + to make Focus + Adjusts the focus of the imageMenu selections Following settings Select the Setup menu to make adjustments toOr rear projection mode Resets all adjustments toImage optimization Using the cursor pad, scroll through the menu selections From the projector control panel or remote control, pressAdjust brightness and contrast. The correct combination Examine the projected image for horizontal noise bars orAdjust the color balance of the projected image Use the Tint option to make the adjustmentsChanges from the default setting are stored in memory for Control panel or remote control commands, you canStorage, cleaning and care MaintenanceReplacing the lamp assembly Half revolution. Grasp the wire handle and gently pull Unlock the lamp assembly by rotating the locking key onLamp assembly straight out of the unit Align the lamp-assembly slide rails with the slide-railSymptom Cause Solution TroubleshootingTroubleshooting guide If at any time you need help Where to get helpYour computer dealer Brasil Polaroid Offices and Service CentersNew Zealand One Year Warranty Maintenance Optional accessory Replacement productAppendix a Parts OG45Appendix a Appendix B Standards