Polaroid Polaview 220 Unlock the lamp assembly by rotating the locking key on, Assembly, Source

Page 34

Maintenance 31

Remove the

Unlock the lamp assembly by rotating the locking key on

lamp assembly

the right side of the lamp assembly counter-clockwise one-

 

half revolution. Grasp the wire handle and gently pull the

 

lamp assembly straight out of the unit.

Replace the

Align the lamp-assembly slide rails with the slide-rail

lamp assembly

channels inside the projector and gently slide the lamp

 

assembly into the projector. When the lamp assembly is

 

properly in seated in the projector, rotate the locking key

 

clockwise one-half revolution.

 

Note: Take care not to touch the lamp in the new assembly.

 

The smallest oil deposit from your finger can significantly

 

shorten the life of the lamp.

Replace the

Align the tabs on the bottom of the door with the slots

lamp-assembly door

in the door opening. Gently push the top of the door into

 

place until the latch snaps into position. Turn the projector

 

on to verify that the lamp functions properly.

 

Note: The removal of the lamp-assembly door activates a

 

safety switch that disconnects electrical power from the

 

lamp assembly. Improper installation of the lamp assembly

 

can prevent the safety switch from being reactivated.

 

Warning: When you replace the lamp assembly, always

 

disconnect the projector from its power source. Do not rely

 

solely on the safety switch to disconnect power from the

 

assembly.

 

Warning: The lamp assembly reaches extremely high tem-

 

peratures during normal operation. If you need to replace

 

the lamp assembly after operating the projector, let the unit

 

cool in Standby mode for at least 30 minutes before

 

attempting to remove the lamp assembly. When you use

 

the Standby mode, power is still being fed to the projector.

 

Do not try to replace the lamp assembly or any electronic

 

components unless you unplug the unit from the power

 

source.

Image 34
Contents Polaview Regarding safety, public health, environment Radiate radio frequency energy and, if not installedProtection against such interference when operated in a Specifications are subject to change without noticeTable of contents Storage, cleaning and care Replacing the lamp Appendix a Parts Appendix B StandardsIntroduction What’s in the box? Items included with the projectorComputer/video compatibility Connector panel Quick startIntroduction Introduction Polaroid Polaview Model 220 Projector and remote control Detailed setupYour Polaview Model 220 Projector Polaroid Polaview Model 220 Projector rear view Getting started Connector panel Computer Inputs Outputs Stereo L R Redrive RSComputer and VCR connections To Mac into the computer monitor port. Plug the end Labeled To VGA into the projector MAC/PC port seeVideo source. Connect the yellow plug at the other end Input composite jacks yellow on the projector connectorConnect one of the yellow RCA composite video cable Panel see the illustration belowUse Sources 1 and 2 to connect Supplying power to the projector Power receptacle and AC power switchUsing the projector Turning on the projectorWant to adjust the rear feet of the projector to position On the control panel or remote control. Adjust the imageSize by using the Zoom control on the control panel or Focus the projected image with the Focus control eitherControl-panel keys Adjusts the focus of the image Image, when used with the cursorDecreases or increases the volume Adjusts the brightness and contrastUsing the remote control Laser pointer Serves as a pointing device Controls the volume, balance, trebleBrightness, contrast, tint, phase Bass of the source connected toFocus + Adjusts the focus of the image Zoom + Zooms in and out. Press + to makeMenu selections Or rear projection mode Select the Setup menu to make adjustments toFollowing settings Resets all adjustments toImage optimization Adjust brightness and contrast. The correct combination From the projector control panel or remote control, pressUsing the cursor pad, scroll through the menu selections Examine the projected image for horizontal noise bars orChanges from the default setting are stored in memory for Use the Tint option to make the adjustmentsAdjust the color balance of the projected image Control panel or remote control commands, you canMaintenance Storage, cleaning and careReplacing the lamp assembly Lamp assembly straight out of the unit Unlock the lamp assembly by rotating the locking key onHalf revolution. Grasp the wire handle and gently pull Align the lamp-assembly slide rails with the slide-railTroubleshooting guide TroubleshootingSymptom Cause Solution Your computer dealer Where to get helpIf at any time you need help Polaroid Offices and Service Centers BrasilNew Zealand One Year Warranty Maintenance Appendix a Parts Replacement productOptional accessory OG45Appendix a Appendix B Standards