Polaroid Polaview 220 Radiate radio frequency energy and, if not installed, CE marking directive

Page 2

FCC Statement

Warning: This equipment generates, uses and can

 

radiate radio frequency energy and, if not installed and

 

used in accordance with the instruction manual, may

 

cause interference to radio communications. It has been

 

tested and found to comply with limits for a Class “A”

 

computing device pursuant to Subpart B of Part 15 of

 

the FCC Rules, which are designed to provide reasonable

 

protection against such interference when operated in a

 

commercial environment. Operation of this equipment in

 

a residential area is likely to cause interference in which

 

case the user, at his own expense, will be required to

 

take whatever measures may be necessary to correct the

 

interference. Shielded cables must be used with this unit to

 

ensure compliance with the Class A FCC limits.

Canadian Notice

This digital apparatus does not exceed the Class A limits

 

for radio noise emissions from digital apparatus set out

 

in the Radio Interference Regulations of the Canadian

 

Department of Communications.

 

Le présent appareil numérique n’émet pas de bruits

 

radioélectriques dépassant les limites applicables aux

 

appareils numériques de la classe A prescrites dans le

 

Règlement sur le brouillage radioélectrique edicté par le

 

ministère des Communications du Canada.

European Notice

Warning: This is a Class A product. In a domestic

 

environment this product may cause radio interference

 

in which case the user may be required to take adequate

 

measures. The “CE” mark certifies that this product

 

satisfies the requirements of the EU (European Union)

 

regarding safety, public health, environment and

 

consumer protection. (“CE” is the abbreviation of

 

Conformité Européenne.) This product is in conformity

 

with the following directives: 73/23/EEC, low voltage

 

directive; 89/33/EEC, EMC directive; 93/68/EEC,

 

“CE” marking directive.

 

© Copyright 1996 Polaroid Corporation. All rights reserved.

 

Specifications are subject to change without notice.

Image 2
Contents Polaview Regarding safety, public health, environment Radiate radio frequency energy and, if not installedProtection against such interference when operated in a Specifications are subject to change without noticeTable of contents Storage, cleaning and care Replacing the lamp Appendix a Parts Appendix B StandardsIntroduction What’s in the box? Items included with the projectorComputer/video compatibility Connector panel Quick startIntroduction Introduction Your Polaview Model 220 Projector Detailed setupPolaroid Polaview Model 220 Projector and remote control Polaroid Polaview Model 220 Projector rear view Getting started Connector panel Computer Inputs Outputs Stereo L R Redrive RSComputer and VCR connections To Mac into the computer monitor port. Plug the end Labeled To VGA into the projector MAC/PC port seeVideo source. Connect the yellow plug at the other end Input composite jacks yellow on the projector connectorConnect one of the yellow RCA composite video cable Panel see the illustration belowUse Sources 1 and 2 to connect Supplying power to the projector Power receptacle and AC power switchUsing the projector Turning on the projectorWant to adjust the rear feet of the projector to position On the control panel or remote control. Adjust the imageSize by using the Zoom control on the control panel or Focus the projected image with the Focus control eitherControl-panel keys Adjusts the focus of the image Image, when used with the cursorDecreases or increases the volume Adjusts the brightness and contrastUsing the remote control Laser pointer Serves as a pointing device Controls the volume, balance, trebleBrightness, contrast, tint, phase Bass of the source connected toFocus + Adjusts the focus of the image Zoom + Zooms in and out. Press + to makeMenu selections Or rear projection mode Select the Setup menu to make adjustments toFollowing settings Resets all adjustments toImage optimization Adjust brightness and contrast. The correct combination From the projector control panel or remote control, pressUsing the cursor pad, scroll through the menu selections Examine the projected image for horizontal noise bars orChanges from the default setting are stored in memory for Use the Tint option to make the adjustmentsAdjust the color balance of the projected image Control panel or remote control commands, you canMaintenance Storage, cleaning and careReplacing the lamp assembly Lamp assembly straight out of the unit Unlock the lamp assembly by rotating the locking key onHalf revolution. Grasp the wire handle and gently pull Align the lamp-assembly slide rails with the slide-railSymptom Cause Solution TroubleshootingTroubleshooting guide If at any time you need help Where to get helpYour computer dealer Polaroid Offices and Service Centers BrasilNew Zealand One Year Warranty Maintenance Appendix a Parts Replacement productOptional accessory OG45Appendix a Appendix B Standards