Polaroid Polaview 220 manual Troubleshooting guide, Symptom Cause Solution

Page 35

5 Troubleshooting

Troubleshooting guide

Symptom

Cause

Solution

 

 

 

Projector does not

Lamp-assembly door

Refer to lamp assembly

turn on;

not closed correctly

replacement procedure

no lights or fan

 

and verify proper installation

 

No power to unit

Try another electrical outlet

 

Blown input power fuse(s)

Call Polaroid Technical Support

 

 

 

Vertical bars appear

Nonstandard computer

Press the IMAGE key and

across the image

clock rate

scroll to PHASE;

 

 

press < > cursor keys

 

 

to remove the bars

 

 

 

Image is upside down

Incorrect projection

Press the SETUP key

 

mode selected

and scroll to LOCATION;

 

 

select DESKTOP or

 

 

CEILING, as applicable

 

 

 

Image rolls vertically

Improper cables/

Check for correct cables

 

loose cables

and snug connection

 

Incorrect computer setup

Check computer video mode

 

 

of operation (see Appendix B:

 

 

Standards)

 

 

 

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Polaview Specifications are subject to change without notice Radiate radio frequency energy and, if not installedProtection against such interference when operated in a Regarding safety, public health, environmentTable of contents Appendix a Parts Appendix B Standards Storage, cleaning and care Replacing the lampIntroduction Items included with the projector What’s in the box?Computer/video compatibility Quick start Connector panelIntroduction Introduction Your Polaview Model 220 Projector Detailed setupPolaroid Polaview Model 220 Projector and remote control Polaroid Polaview Model 220 Projector rear view Getting started Computer Inputs Outputs Stereo L R Redrive RS Connector panelComputer and VCR connections Labeled To VGA into the projector MAC/PC port see To Mac into the computer monitor port. Plug the endPanel see the illustration below Input composite jacks yellow on the projector connectorConnect one of the yellow RCA composite video cable Video source. Connect the yellow plug at the other endUse Sources 1 and 2 to connect Power receptacle and AC power switch Supplying power to the projectorTurning on the projector Using the projectorFocus the projected image with the Focus control either On the control panel or remote control. Adjust the imageSize by using the Zoom control on the control panel or Want to adjust the rear feet of the projector to positionControl-panel keys Adjusts the brightness and contrast Image, when used with the cursorDecreases or increases the volume Adjusts the focus of the imageUsing the remote control Bass of the source connected to Controls the volume, balance, trebleBrightness, contrast, tint, phase Laser pointer Serves as a pointing deviceZoom + Zooms in and out. Press + to make Focus + Adjusts the focus of the imageMenu selections Resets all adjustments to Select the Setup menu to make adjustments toFollowing settings Or rear projection modeImage optimization Examine the projected image for horizontal noise bars or From the projector control panel or remote control, pressUsing the cursor pad, scroll through the menu selections Adjust brightness and contrast. The correct combinationControl panel or remote control commands, you can Use the Tint option to make the adjustmentsAdjust the color balance of the projected image Changes from the default setting are stored in memory forStorage, cleaning and care MaintenanceReplacing the lamp assembly Align the lamp-assembly slide rails with the slide-rail Unlock the lamp assembly by rotating the locking key onHalf revolution. Grasp the wire handle and gently pull Lamp assembly straight out of the unitSymptom Cause Solution TroubleshootingTroubleshooting guide If at any time you need help Where to get helpYour computer dealer Brasil Polaroid Offices and Service CentersNew Zealand One Year Warranty Maintenance OG45 Replacement productOptional accessory Appendix a PartsAppendix a Appendix B Standards
Top Page Image Contents