Pioneer PDSP-1 Bass Management Sub Woofer Yes LFE Level, Sub Woofer Menu No/LFE to panel Yes

Page 30

	Changing		Calling Up a Room	Video and Audio	Adjusting	Displaying the
		Adjusting the Tone		Timing
	Surround Sound		Sound Setting		Surround Effects	Data Screen
				Compensations

Sub Woofer / Bass Management

This menu allows you to set the unit for a sub-woofer, and LFE channel ON/OFF.

1- 3 (Same as steps 1 - 3 on P27, “Test Signal”)

4Using the buttons, select “Bass Management”, and press the ENTER button. The following screen appears:

Bass Management
1	Sub Woofer	Yes
2	LFE Level	0.0dB

LFE channel output level

Notes:

LFE means “Low Frequency Effect”.

If “Sub Woofer” is set to “Yes”, use the buttons to select “LFE level”, then use the buttons to adjust the output level.

Setting range: 0.0 dB – 12.0 dB

5Using the buttons, select “Sub Woofer”, then press the ENTER button. The following screen appears:

Sub Woofer: No

(LFE will not be output from any channel)

Sub Woofer Menu

1No

2No/LFE to panel

3Yes

Sub Woofer: No/LFE to panel

(LFE is output from digital sound projector)

Sub Woofer: Yes

(LFE is output to Sub Woofer)

6Using the buttons, select either “No,” “No/LFE to panel,” or “Yes,” then press the ENTER button.

Note:

When you’re finished, you can press the MENU button repeatedly to return to previous screens.

“SUB WOOFER OUTPUT connectors” P13

30

Image 30

Contents PDSP-1 Installation Preface For U.S. modelMaintenance of External Surfaces Regarding InstallationContents Features Beam control technologySound settings to match your room’s characteristics Confirm All Accessories These operating InstructionsSpecifications Audio SectionFront Panel Range of the Remote Control Unit Parts and their FunctionsAttaching the Front Grille Rear Panel Video outputs Monitor Output connectors About the Input/Output ConnectorsAudio output Output Optical connector SUB Woofer Output connectorsRemote Control Unit About the Remote Control Unit Buttons hard keysSetting the Basic Information on the Remote Control Unit Set the touch panel to the Home menuIllustration depicts U.S. model Using the Remote Control Unit Using Digital Sound ProjectorComponent Operation Menu Display About the Home Menu About the Pdsp digital sound projector menu Operating Menus for Other Components Using Watching TelevisionWatching a DVD Accompanying three menus are used to operate the DVD playerUsing a Pioneer DVD Recorder RecordingPerform recording operations on menu 1/2 at left Playback/Editing Following four menus are used to operate the DVD recorderDigital Sound Pr ojector Selecting the Audio ModeUsing Plii Movie Plii Music Pro Logic StereoMono Enhancing Monaural Sources Changing Surround Sound Adjusting the Sound Test Signal Use the touch panel to select the Pdsp menuSurround L LeftRight Surround RLeft To edit Press Enter or Menu to exit Level 0dB Surround Setup LeftAux Center Mute Bass Management Noise Source Off Changing Each Channel’s Output LevelSub Woofer Menu No/LFE to panel Yes Same as steps 1 3 on P27, Test SignalBass Management Sub Woofer Yes LFE Level Sub Woofer / Bass ManagementTreble Level 0dB Adjusting the ToneAll Ch Tone Control Bass Level 0dB All Ch To edit Press Enter or Menu to exit 0dB Bass +Calling Up a Room Sound Setting Recall from MemoryVideo and Audio Timing Compensations Lipsync delay Lipsync delay To edit Press Enter or Menu to exit Delay 0msAdjusting Surround Effects Stereo Mode Menu Image width Image width value Plii ModePlii Mode Plii Off Movie Music Pro Logic Fine Tuning the Plii Music ModeStereo Mode Menu Image width Panorama Off Center width DimensionWidth Status Source Input 2 D Memory ModeDisplaying the Data Screen Press the Enter buttonTroubleshooting Additional Information Table of Remote Control Unit Menu Displays Dvdplayer Channel Menu Enter VOLUME,MUTE Index Terms displayed in menus Terms on front panel / rear panelSymbols and terms on remote control unit / touch panel Terminology in these operating instructions03F00001