Planar PD7170 operation manual Exhaust Vent

Page 20

Controls and Functions

ENTER ( )

Press to select a highlighted menu item or confirm a changed setting.

When no menu is present on-screen, press ENTER to access the motorized lens focus control. Press ENTER again to access the motorized lens zoom control. Press ENTER yet again to access the motorized lens shift control.

Use the and buttons to adjust focus, zoom or vertical lens position. Use the and buttons to adjust horizontal lens position.

MENU

Press this button to show or hide the OSD menus.

•POWER BUTTON/STATUS LED Indicates projector status as follows:

• Solid green = AC power present, ready to turn on (lamp not lit)

•Flashing green = lamp is warming up or cooling down; keypad functions not allowed

•Off = Lamp lit, projector functioning normally

•Alternating green/red = Lamp problem (door open, unable to strike, end of life), user intervention likely to fix problem

•Flashing red = Over temperature, user intervention (clear vents, turn on AC) may fix problem

•Solid red = Error that requires servicing (fan fail, Power-on self-test fail etc.)

•EXHAUST VENT

Warm air exits the projector through this vent. Ensure that it is not blocked.

•INTAKE VENT

Internal fans draw cool air into the projector through this vent.

•PROJECTION LENS

The inside of the lens barrel is threaded to accommodate a standard, 72-mm lens filter. For example, with a smaller screen you can install a neutral-density filter to reduce the overall light output.

If needed, a light shield accessory is provided with the lens to minimize stray light emissions. (Use it only when the vertical offset is 50% of the screen height or greater.) The light shield attaches to the end of the lens (or to the filter, if used).

•FRONT IR SENSOR

Receives infrared signals from the remote control unit.

6	Planar PD7170 Installation/Operation Manual

Image 20

Contents PD7170 Home Theater Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsXii List Of Figures List Of Figures Carriage return must be used after each command or IntroductionAbout This Manual Target AudienceUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsParts List Optional AccessoriesControls and Functions PD7170 at a GlanceExhaust Vent Planar Logo Badge Rear Cover PD7170 Rear Panel ComponentPD7170 Remote Control IR InputEnter PIP Controls and Functions Operation InstallationRemote Control IR Reception Angles Quick Setup Installation OverviewInstallation should be performed by a qualified custom Video installation specialistInstallation Projector Installation OptionsInstallation Type ConsiderationsAmbient Light Throw DistancePosition PD7170 Lens Options and Throw RatiosVertical and Horizontal Lens Shift Width, as shown in -4 and FigureVertical lens shift figures are for ceiling mount Folded OpticsLens Replacement Lens Motor Connector Trim RingMounting the PD7170 Connections to the PD7170Connector Panel Access Highest video quality because the signal is carried Connecting Source Components to the PD7170Use the Hdmi inputs whenever possible. This ensures Component output into the projectorRGB Connections Component Video Connections 10. Composite and S-Video Connections Communications on RS-232 ControllerConnection Connecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentFocus Zoom Lens Shift Turning on the Power Lens AdjustmentsConnecting to AC Power Changing the OSD Language Lens shift exceeds 50 per cent of the screen heightAdjusting the Picture Orientation Rear Projection Ceiling ModeInstallation Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus PD7170 OSD Menu Structure DynamicBlack to Off before adjusting Brightness, Contrast Other image quality settings in this menu refer toPIP source, switch to the PIP source thereby making it Active source, adjust the controls and then switch169 Aspect Ratio SettingsAspect Geometry of Projected Image Letterbox Native You must enter a passcode to access the Save ISF Sub-menuTypical Pluge Pattern for Adjusting Brightness Brightness and Contrast controls are interactive. a change Achieve the optimum settingChange to the other in order to achieve the optimum setting Operation Crop Overscan ExamplesSource Select Sub-Menu Advanced PD7170 Advanced MenuOperation Color X/y Color Gamut ValuesTo the same frame rate as the main source RGB Adjust Sub-Menu Generally, higher Gain settings reduce the image contrast Higher Offset settings reduce the image brightnessAdjust the Phase after adjusting Tracking see below. If Remove high-frequency noise from the signalSome shimmer from a video or Hdtv source persists, use Noise Reduction controls described on page 46 toSystem 11. PD7170 System MenuIf Scart is enabled, both Component 1 and Video must be If either Component 1 or Video is enabled, Scart must beDisabled PIP 14. PIP Split-Screen Mode Control 15. PD7170 Control MenuOperation Language Service 16. PD7170 Service MenuOperation OSD menus are not available when in test pattern ModeMaintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart LED is flashing red PD7170 internal Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.brig Operations Commands Operations Control Commands Function Action on unitSerial Commands ValuesSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source PD7170 Specifications SpecificationsPD7170 Specifications Native Resolution PerformanceMicrodisplay Aspect RatiosDimensions Weight without lensOperating Temperature Universal Power SupplyPD7170 Dimensions 1shows the PD7170 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G Page Part No -0882-01 rev. a May