Planar PD7170 operation manual Source Select Sub-Menu

Page 62

Operation

Source Select: To select a video source, press or to highlight Source Select, then press ENTER. This displays the Source Select sub-menu, shown in Figure 4-7.

The default source selection is HDMI 1. All sources that are not available per the source enable function (refer to Source Enable on page 56) are grayed out.

Figure 4-7. Source Select Sub-Menu

PIP Select: To select a PIP (secondary) video source, press or to highlight PIP Select, then press ENTER. The default PIP selection is Off.

All sources that are not available per the source enable function (refer to Source Enable on page 56) are grayed out.

All sources that cannot be used for PIP due to a shared electronic path with the Active source are grayed out. The PIP source is a saved setting for each source, like brightness and contrast.

If for some reason the current PIP source becomes invalid (by disabling it in the source enable menu, for instance), PIP Select automatically resets to Off.

Resync: If the projected image becomes unstable or degraded, press or to highlight Resync, then press ENTER. This causes a re-acquisition of the active source and the PIP source, if present. It also changes any Fine Sync settings (described on page 53) for this timing to the default setting.

48

Planar PD7170 Installation/Operation Manual

Image 62
Contents PD7170 Home Theater Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsXii List Of Figures List Of Figures About This Manual Carriage return must be used after each command orIntroduction Target AudienceUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsParts List Optional AccessoriesControls and Functions PD7170 at a GlanceExhaust Vent Planar Logo Badge Rear Cover PD7170 Rear Panel ComponentPD7170 Remote Control IR InputEnter PIP Controls and Functions Operation InstallationRemote Control IR Reception Angles Installation should be performed by a qualified custom Quick SetupInstallation Overview Video installation specialistInstallation Type InstallationProjector Installation Options ConsiderationsAmbient Light Throw DistancePosition PD7170 Lens Options and Throw RatiosVertical and Horizontal Lens Shift Width, as shown in -4 and FigureVertical lens shift figures are for ceiling mount Folded OpticsLens Replacement Lens Motor Connector Trim RingMounting the PD7170 Connections to the PD7170Connector Panel Access Use the Hdmi inputs whenever possible. This ensures Highest video quality because the signal is carriedConnecting Source Components to the PD7170 Component output into the projectorRGB Connections Component Video Connections 10. Composite and S-Video Connections Communications on RS-232 ControllerConnection Trigger Output to External Connecting 12-VoltConnecting an External IR Theater EquipmentFocus Zoom Lens Shift Turning on the Power Lens AdjustmentsConnecting to AC Power Changing the OSD Language Lens shift exceeds 50 per cent of the screen heightAdjusting the Picture Orientation Rear Projection Ceiling ModeInstallation Selecting an Aspect Ratio OperationSelecting Video Memory Selecting An Input SourcePIP Input Source Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations MainUsing the On-Screen Menus PD7170 OSD Menu Structure PIP source, switch to the PIP source thereby making it DynamicBlack to Off before adjusting Brightness, ContrastOther image quality settings in this menu refer to Active source, adjust the controls and then switch169 Aspect Ratio SettingsAspect Geometry of Projected Image Letterbox Native You must enter a passcode to access the Save ISF Sub-menuTypical Pluge Pattern for Adjusting Brightness Brightness and Contrast controls are interactive. a change Achieve the optimum settingChange to the other in order to achieve the optimum setting Operation Crop Overscan ExamplesSource Select Sub-Menu Advanced PD7170 Advanced MenuOperation Color X/y Color Gamut ValuesTo the same frame rate as the main source RGB Adjust Sub-Menu Generally, higher Gain settings reduce the image contrast Higher Offset settings reduce the image brightnessSome shimmer from a video or Hdtv source persists, use Adjust the Phase after adjusting Tracking see below. IfRemove high-frequency noise from the signal Noise Reduction controls described on page 46 toSystem 11. PD7170 System MenuIf Scart is enabled, both Component 1 and Video must be If either Component 1 or Video is enabled, Scart must beDisabled PIP 14. PIP Split-Screen Mode Control 15. PD7170 Control MenuOperation Language Service 16. PD7170 Service MenuOperation OSD menus are not available when in test pattern ModeMaintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart LED is flashing red PD7170 internal Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.brig Operations Commands Operations Control Commands Function Action on unitSerial Commands ValuesSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source PD7170 Specifications SpecificationsPD7170 Specifications Microdisplay Native ResolutionPerformance Aspect RatiosOperating Temperature DimensionsWeight without lens Universal Power SupplyPD7170 Dimensions 1shows the PD7170 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G Page Part No -0882-01 rev. a May