Planar PD7170 operation manual Installation, Remote Control, Operation

Page 27

Installation

Installation

To install batteries in the remote control:

1.Slide the battery compartment cover in the direction of the arrow to remove it.

2.Install two AA batteries with the correct polarity.

3.Replace the cover.

3.1

Remote Control

1.

2.

3.

• Make sure that the battery polarities are correct when installing the batteries.

Notes on Batteries

•Do not mix an old battery with a new one or different types of batteries.

•If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

•	In most situations, you can simply point the remote control at the screen	Notes on Remote Control
	which will reflect the IR signal from the remote back toward the IR receiver on	Operation
	the projector. In some cases, however, ambient conditions may prevent this.
	If so, point the remote control at the projector and try again.
•	If the effective range of the remote control decreases, or it stops working,
	replace the batteries with new ones.
•	The remote control may fail to operate if the infrared remote sensor is
	exposed to bright sunlight or fluorescent lighting.

Planar PD7170 Installation/Operation Manual

13

Image 27

Contents PD7170 Home Theater Projector Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Maintenance and TroubleshootingSerial Communications SpecificationsXii List Of Figures List Of Figures Target Audience Carriage return must be used after each command orIntroduction About This ManualIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Parts ListPD7170 at a Glance Controls and FunctionsExhaust Vent Planar Logo Badge Rear Cover Component PD7170 Rear PanelIR Input PD7170 Remote ControlEnter PIP Controls and Functions Installation Remote ControlOperation IR Reception Angles Video installation specialist Quick SetupInstallation Overview Installation should be performed by a qualified customConsiderations InstallationProjector Installation Options Installation TypeThrow Distance Ambient LightPD7170 Lens Options and Throw Ratios Vertical and HorizontalPosition Width, as shown in -4 and Figure Lens ShiftFolded Optics Vertical lens shift figures are for ceiling mountLens Replacement Trim Ring Lens Motor ConnectorConnections to the PD7170 Mounting the PD7170Connector Panel Access Component output into the projector Highest video quality because the signal is carriedConnecting Source Components to the PD7170 Use the Hdmi inputs whenever possible. This ensuresRGB Connections Component Video Connections 10. Composite and S-Video Connections RS-232 Controller ConnectionCommunications on Theater Equipment Connecting 12-VoltConnecting an External IR Trigger Output to ExternalTurning on the Power Lens Adjustments Connecting to AC PowerFocus Zoom Lens Shift Lens shift exceeds 50 per cent of the screen height Changing the OSD LanguageRear Projection Ceiling Mode Adjusting the Picture OrientationInstallation Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect RatioMain Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus PD7170 OSD Menu Structure Active source, adjust the controls and then switch DynamicBlack to Off before adjusting Brightness, ContrastOther image quality settings in this menu refer to PIP source, switch to the PIP source thereby making itAspect Ratio Settings Aspect Geometry of Projected Image169 Letterbox Native Sub-menu You must enter a passcode to access the Save ISFTypical Pluge Pattern for Adjusting Brightness Achieve the optimum setting Change to the other in order to achieve the optimum settingBrightness and Contrast controls are interactive. a change Operation Overscan Examples CropSource Select Sub-Menu PD7170 Advanced Menu AdvancedOperation X/y Color Gamut Values To the same frame rate as the main sourceColor RGB Adjust Sub-Menu Higher Offset settings reduce the image brightness Generally, higher Gain settings reduce the image contrastNoise Reduction controls described on page 46 to Adjust the Phase after adjusting Tracking see below. IfRemove high-frequency noise from the signal Some shimmer from a video or Hdtv source persists, use11. PD7170 System Menu SystemIf either Component 1 or Video is enabled, Scart must be DisabledIf Scart is enabled, both Component 1 and Video must be PIP 14. PIP Split-Screen Mode 15. PD7170 Control Menu ControlOperation Language 16. PD7170 Service Menu ServiceOperation Mode OSD menus are not available when in test patternLamp Replacement Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution LED is flashing red PD7170 internal Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.brig Operations Control Commands Function Action on unit Operations CommandsValues Serial CommandsSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source Specifications PD7170 SpecificationsPD7170 Specifications Aspect Ratios Native ResolutionPerformance MicrodisplayUniversal Power Supply DimensionsWeight without lens Operating Temperature1shows the PD7170 dimensions, in millimeters PD7170 DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page Part No -0882-01 rev. a May