Planar PD7170 operation manual Lens Shift, Width, as shown in -4 and Figure

Page 33

 

Installation

 

 

You can use the lens shift controls on the projector to center the image on the

Vertical and Horizontal

screen. Lens shift is generally expressed as a percentage of the screen height or

Lens Shift

width, as shown in Figure 3-4and Figure 3-5.

 

Screen Center

0%

50% Height

Lens Shift

(0.5 x H)

100% Height

Lens Shift

(1.0 x H)

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example.

Figure 3-4. Vertical Lens Shift (Example Only)

100% Width Lens Shift

(1.0 x W)

50% Width Lens Shift

(0.5 x W)

Screen Center

0%

Screen Width (W)

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or projector is used in this example.

Figure 3-5. Horizontal Lens Shift (Example Only)

Planar PD7170 Installation/Operation Manual

19

Image 33
Contents PD7170 Home Theater Projector Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Maintenance and TroubleshootingSerial Communications SpecificationsXii List Of Figures List Of Figures Introduction Carriage return must be used after each command orAbout This Manual Target AudienceIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Parts ListPD7170 at a Glance Controls and FunctionsExhaust Vent Planar Logo Badge Rear Cover Component PD7170 Rear PanelIR Input PD7170 Remote ControlEnter PIP Controls and Functions Installation Remote ControlOperation IR Reception Angles Installation Overview Quick SetupInstallation should be performed by a qualified custom Video installation specialistProjector Installation Options InstallationInstallation Type ConsiderationsThrow Distance Ambient LightPD7170 Lens Options and Throw Ratios Vertical and HorizontalPosition Width, as shown in -4 and Figure Lens ShiftFolded Optics Vertical lens shift figures are for ceiling mountLens Replacement Trim Ring Lens Motor ConnectorConnections to the PD7170 Mounting the PD7170Connector Panel Access Connecting Source Components to the PD7170 Highest video quality because the signal is carriedUse the Hdmi inputs whenever possible. This ensures Component output into the projectorRGB Connections Component Video Connections 10. Composite and S-Video Connections RS-232 Controller ConnectionCommunications on Connecting an External IR Connecting 12-VoltTrigger Output to External Theater EquipmentTurning on the Power Lens Adjustments Connecting to AC PowerFocus Zoom Lens Shift Lens shift exceeds 50 per cent of the screen height Changing the OSD LanguageRear Projection Ceiling Mode Adjusting the Picture OrientationInstallation Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input SourceAvailable Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source MainUsing the On-Screen Menus PD7170 OSD Menu Structure Other image quality settings in this menu refer to DynamicBlack to Off before adjusting Brightness, ContrastPIP source, switch to the PIP source thereby making it Active source, adjust the controls and then switchAspect Ratio Settings Aspect Geometry of Projected Image169 Letterbox Native Sub-menu You must enter a passcode to access the Save ISFTypical Pluge Pattern for Adjusting Brightness Achieve the optimum setting Change to the other in order to achieve the optimum settingBrightness and Contrast controls are interactive. a change Operation Overscan Examples CropSource Select Sub-Menu PD7170 Advanced Menu AdvancedOperation X/y Color Gamut Values To the same frame rate as the main sourceColor RGB Adjust Sub-Menu Higher Offset settings reduce the image brightness Generally, higher Gain settings reduce the image contrastRemove high-frequency noise from the signal Adjust the Phase after adjusting Tracking see below. IfSome shimmer from a video or Hdtv source persists, use Noise Reduction controls described on page 46 to11. PD7170 System Menu SystemIf either Component 1 or Video is enabled, Scart must be DisabledIf Scart is enabled, both Component 1 and Video must be PIP 14. PIP Split-Screen Mode 15. PD7170 Control Menu ControlOperation Language 16. PD7170 Service Menu ServiceOperation Mode OSD menus are not available when in test patternLamp Replacement Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution LED is flashing red PD7170 internal Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.brig Operations Control Commands Function Action on unit Operations CommandsValues Serial CommandsSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source Specifications PD7170 SpecificationsPD7170 Specifications Performance Native ResolutionMicrodisplay Aspect RatiosWeight without lens DimensionsOperating Temperature Universal Power Supply1shows the PD7170 dimensions, in millimeters PD7170 DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page Part No -0882-01 rev. a May