Planar operation manual Controls and Functions, PD7170 at a Glance

Page 19

Controls and Functions

Controls and Functions

Figure 2-1and Figure 2-2show the key PD7170 components.

Top IR Sensor

Power Button/

Status LED

System Keypad

Exhaust
Vent	Intake
	Vent

2.1

PD7170 at a Glance

Projection Lens

Front IR Sensor

Figure 2-1. PD7170 Front/Side View
• TOP IR SENSOR
Receives infrared signals from the remote control unit.
• SYSTEM KEYPAD
Provides an alternative to using the remote control unit to select a source or		SOURCE
navigate the on-screen display (OSD) controls.		SOURCE
SOURCE		▲
Use this button to select a video source.
Cursor Buttons ( , , , )	◄	►
Use these buttons to select items or settings, adjust settings or switch display
patterns.		▲
		▲
		MENU

Planar PD7170 Installation/Operation Manual

5

Image 19

Contents PD7170 Home Theater Projector Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Maintenance and TroubleshootingSerial Communications SpecificationsXii List Of Figures List Of Figures Target Audience Carriage return must be used after each command orIntroduction About This ManualIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Parts ListPD7170 at a Glance Controls and FunctionsExhaust Vent Planar Logo Badge Rear Cover Component PD7170 Rear PanelIR Input PD7170 Remote ControlEnter PIP Controls and Functions Remote Control InstallationOperation IR Reception Angles Video installation specialist Quick SetupInstallation Overview Installation should be performed by a qualified customConsiderations InstallationProjector Installation Options Installation TypeThrow Distance Ambient LightVertical and Horizontal PD7170 Lens Options and Throw RatiosPosition Width, as shown in -4 and Figure Lens ShiftFolded Optics Vertical lens shift figures are for ceiling mountLens Replacement Trim Ring Lens Motor ConnectorConnections to the PD7170 Mounting the PD7170Connector Panel Access Component output into the projector Highest video quality because the signal is carriedConnecting Source Components to the PD7170 Use the Hdmi inputs whenever possible. This ensuresRGB Connections Component Video Connections 10. Composite and S-Video Connections Connection RS-232 ControllerCommunications on Theater Equipment Connecting 12-VoltConnecting an External IR Trigger Output to ExternalConnecting to AC Power Turning on the Power Lens AdjustmentsFocus Zoom Lens Shift Lens shift exceeds 50 per cent of the screen height Changing the OSD LanguageRear Projection Ceiling Mode Adjusting the Picture OrientationInstallation Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect RatioMain Using Picture-In-Picture PIPAvailable Main and PIP Source Combinations PIP Input SourceUsing the On-Screen Menus PD7170 OSD Menu Structure Active source, adjust the controls and then switch DynamicBlack to Off before adjusting Brightness, ContrastOther image quality settings in this menu refer to PIP source, switch to the PIP source thereby making itAspect Geometry of Projected Image Aspect Ratio Settings169 Letterbox Native Sub-menu You must enter a passcode to access the Save ISFTypical Pluge Pattern for Adjusting Brightness Change to the other in order to achieve the optimum setting Achieve the optimum settingBrightness and Contrast controls are interactive. a change Operation Overscan Examples CropSource Select Sub-Menu PD7170 Advanced Menu AdvancedOperation To the same frame rate as the main source X/y Color Gamut ValuesColor RGB Adjust Sub-Menu Higher Offset settings reduce the image brightness Generally, higher Gain settings reduce the image contrastNoise Reduction controls described on page 46 to Adjust the Phase after adjusting Tracking see below. IfRemove high-frequency noise from the signal Some shimmer from a video or Hdtv source persists, use11. PD7170 System Menu SystemDisabled If either Component 1 or Video is enabled, Scart must beIf Scart is enabled, both Component 1 and Video must be PIP 14. PIP Split-Screen Mode 15. PD7170 Control Menu ControlOperation Language 16. PD7170 Service Menu ServiceOperation Mode OSD menus are not available when in test patternLamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution LED is flashing red PD7170 internal Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.brig Operations Control Commands Function Action on unit Operations CommandsValues Serial CommandsSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source PD7170 Specifications SpecificationsPD7170 Specifications Aspect Ratios Native ResolutionPerformance MicrodisplayUniversal Power Supply DimensionsWeight without lens Operating Temperature1shows the PD7170 dimensions, in millimeters PD7170 DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page Part No -0882-01 rev. a May