Planar PD7170 operation manual Pip

Page 25

Controls and Functions

8.Picture Adjustment Buttons:

Contrast

Press to adjust white level.

Brightness

Press to adjust black level.

Sharpness (SHARP)

Press to adjust sharpness.

Gamma (GAMMA)

Press to select a gamma curve.

Overscan (OS)

Press to select an overscan mode.

Noise Reduction (NR)

Press to adjust noise reduction level.

9.LIGHT

Press momentarily to activate remote backlighting. Press and hold for 5 to 7 seconds to illuminate the projector rear panel, to facilitate connecting cables in a dark room.

10.Picture-In-Picture (PIP) Controls:

PIP

Press repeatedly to activate/deactivate PIP mode or select the desired PIP image source.

SWAP

Press to swap the PIP image with the active source image.

Planar PD7170 Installation/Operation Manual

11

Image 25

Contents PD7170 Home Theater Projector Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Table of Contents Operation Maintenance and TroubleshootingSerial Communications SpecificationsXii List Of Figures List Of Figures Introduction Carriage return must be used after each command orAbout This Manual Target AudienceIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Parts ListPD7170 at a Glance Controls and FunctionsExhaust Vent Planar Logo Badge Rear Cover Component PD7170 Rear PanelIR Input PD7170 Remote ControlEnter PIP Controls and Functions Remote Control InstallationOperation IR Reception Angles Installation Overview Quick SetupInstallation should be performed by a qualified custom Video installation specialistProjector Installation Options InstallationInstallation Type ConsiderationsThrow Distance Ambient LightVertical and Horizontal PD7170 Lens Options and Throw RatiosPosition Width, as shown in -4 and Figure Lens ShiftFolded Optics Vertical lens shift figures are for ceiling mountLens Replacement Trim Ring Lens Motor ConnectorConnections to the PD7170 Mounting the PD7170Connector Panel Access Connecting Source Components to the PD7170 Highest video quality because the signal is carriedUse the Hdmi inputs whenever possible. This ensures Component output into the projectorRGB Connections Component Video Connections 10. Composite and S-Video Connections Connection RS-232 ControllerCommunications on Connecting an External IR Connecting 12-VoltTrigger Output to External Theater EquipmentConnecting to AC Power Turning on the Power Lens AdjustmentsFocus Zoom Lens Shift Lens shift exceeds 50 per cent of the screen height Changing the OSD LanguageRear Projection Ceiling Mode Adjusting the Picture OrientationInstallation Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input SourceAvailable Main and PIP Source Combinations Using Picture-In-Picture PIPPIP Input Source MainUsing the On-Screen Menus PD7170 OSD Menu Structure Other image quality settings in this menu refer to DynamicBlack to Off before adjusting Brightness, ContrastPIP source, switch to the PIP source thereby making it Active source, adjust the controls and then switchAspect Geometry of Projected Image Aspect Ratio Settings169 Letterbox Native Sub-menu You must enter a passcode to access the Save ISFTypical Pluge Pattern for Adjusting Brightness Change to the other in order to achieve the optimum setting Achieve the optimum settingBrightness and Contrast controls are interactive. a change Operation Overscan Examples CropSource Select Sub-Menu PD7170 Advanced Menu AdvancedOperation To the same frame rate as the main source X/y Color Gamut ValuesColor RGB Adjust Sub-Menu Higher Offset settings reduce the image brightness Generally, higher Gain settings reduce the image contrastRemove high-frequency noise from the signal Adjust the Phase after adjusting Tracking see below. IfSome shimmer from a video or Hdtv source persists, use Noise Reduction controls described on page 46 to11. PD7170 System Menu SystemDisabled If either Component 1 or Video is enabled, Scart must beIf Scart is enabled, both Component 1 and Video must be PIP 14. PIP Split-Screen Mode 15. PD7170 Control Menu ControlOperation Language 16. PD7170 Service Menu ServiceOperation Mode OSD menus are not available when in test patternLamp Replacement Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution LED is flashing red PD7170 internal Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.brig Operations Control Commands Function Action on unit Operations CommandsValues Serial CommandsSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source PD7170 Specifications SpecificationsPD7170 Specifications Performance Native ResolutionMicrodisplay Aspect RatiosWeight without lens DimensionsOperating Temperature Universal Power Supply1shows the PD7170 dimensions, in millimeters PD7170 DimensionsSupported Timings Supported Signal Timings by InputPAL-B/G Page Part No -0882-01 rev. a May