Planar PD7170 operation manual FCC Part

Page 8

The Technical Construction file required by this Directive is maintained at the corporate headquarters of Planar Systems, Inc., 1195 NW Compton Drive, Beaverton, OR 97006.

Date of Declaration: February 2008

FCC PART 15:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA (ICES-003):

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IMPORTANT RECYCLE INSTRUCTIONS

Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws.

For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG.

DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European Union and other European countries with separate collection programs)

This symbol found on your product or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.

viii

Planar PD7170 Installation/Operation Manual

Page 7 Page 9
Image 8
Page 7 Page 9
Contents PD7170 Home Theater Projector Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersContact a Planar Authorized Service Center to Obtain Service Additional Information Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Table of Contents Maintenance and Troubleshooting OperationSpecifications Serial CommunicationsXii List Of Figures List Of Figures Carriage return must be used after each command or IntroductionAbout This Manual Target AudienceUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsParts List Optional AccessoriesControls and Functions PD7170 at a GlanceExhaust Vent Planar Logo Badge Rear Cover PD7170 Rear Panel ComponentPD7170 Remote Control IR InputEnter PIP Controls and Functions Operation InstallationRemote Control IR Reception Angles Quick Setup Installation OverviewInstallation should be performed by a qualified custom Video installation specialistInstallation Projector Installation OptionsInstallation Type ConsiderationsAmbient Light Throw DistancePosition PD7170 Lens Options and Throw RatiosVertical and Horizontal Lens Shift Width, as shown in -4 and FigureVertical lens shift figures are for ceiling mount Folded OpticsLens Replacement Lens Motor Connector Trim RingMounting the PD7170 Connections to the PD7170Connector Panel Access Highest video quality because the signal is carried Connecting Source Components to the PD7170Use the Hdmi inputs whenever possible. This ensures Component output into the projectorRGB Connections Component Video Connections 10. Composite and S-Video Connections Communications on RS-232 ControllerConnection Connecting 12-Volt Connecting an External IRTrigger Output to External Theater EquipmentFocus Zoom Lens Shift Turning on the Power Lens AdjustmentsConnecting to AC Power Changing the OSD Language Lens shift exceeds 50 per cent of the screen heightAdjusting the Picture Orientation Rear Projection Ceiling ModeInstallation Operation Selecting Video MemorySelecting an Aspect Ratio Selecting An Input SourceUsing Picture-In-Picture PIP Available Main and PIP Source CombinationsPIP Input Source MainUsing the On-Screen Menus PD7170 OSD Menu Structure DynamicBlack to Off before adjusting Brightness, Contrast Other image quality settings in this menu refer toPIP source, switch to the PIP source thereby making it Active source, adjust the controls and then switch169 Aspect Ratio SettingsAspect Geometry of Projected Image Letterbox Native You must enter a passcode to access the Save ISF Sub-menuTypical Pluge Pattern for Adjusting Brightness Brightness and Contrast controls are interactive. a change Achieve the optimum settingChange to the other in order to achieve the optimum setting Operation Crop Overscan ExamplesSource Select Sub-Menu Advanced PD7170 Advanced MenuOperation Color X/y Color Gamut ValuesTo the same frame rate as the main source RGB Adjust Sub-Menu Generally, higher Gain settings reduce the image contrast Higher Offset settings reduce the image brightnessAdjust the Phase after adjusting Tracking see below. If Remove high-frequency noise from the signalSome shimmer from a video or Hdtv source persists, use Noise Reduction controls described on page 46 toSystem 11. PD7170 System MenuIf Scart is enabled, both Component 1 and Video must be If either Component 1 or Video is enabled, Scart must beDisabled PIP 14. PIP Split-Screen Mode Control 15. PD7170 Control MenuOperation Language Service 16. PD7170 Service MenuOperation OSD menus are not available when in test pattern ModeMaintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart LED is flashing red PD7170 internal Maintenance and Troubleshooting Key Commands Serial CommunicationsSerial Command Key Names and IR Codes RS232 Remote Button IR Code Description Keyname SetGam.brig Operations Commands Operations Control Commands Function Action on unitSerial Commands ValuesSave.isf Source.sel = ? Dblack = ? Blank.screen = ? Act.source PD7170 Specifications SpecificationsPD7170 Specifications Native Resolution PerformanceMicrodisplay Aspect RatiosDimensions Weight without lensOperating Temperature Universal Power SupplyPD7170 Dimensions 1shows the PD7170 dimensions, in millimetersSupported Signal Timings by Input Supported TimingsPAL-B/G Page Part No -0882-01 rev. a May
Top Page Image Contents