Optoma Technology XX152 N manual Precautions

Page 3

Usage Notice

Precautions

Please follow all warnings, precautions and mainte- nance as recommended in this user’s guide.

NOTE

When the lamp reaches the end of its life, the pro- jector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the proce- dures listed under “Replacing the Lamp” section.

▀■ Warning-

▀■ Warning-

▀■ Warning-

▀■ Warning-

▀■ Warning-

▀■ Warning-

▀■ Warning-

▀■ Warning-

▀■ Warning-

Do not look into the projector’s lens when the lamp is on. The bright light may hurt your eyes.

To reduce the risk of fi re or electric shock, do not expose this projector to rain or moisture.

Please do not open or disassemble the projec- tor as this may cause electric shock.

When replacing the lamp, please allow the unit to cool down.

This projector will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages.

Reset the “Lamp Reset” function from the on- screen display “SystemLamp Setting” menu after replacing the lamp module.

When switching the projector off, please ensure the cooling cycle has been completed before disconnecting power. Allow 90 seconds for the projector to cool down.

Do not use lens cap when projector is in opera- tion.

When the lamp is approaching to the end of its life time, the message “Replacement sug- gested” will show on the screen. Please contact your local reseller or service center to change the lamp as soon as possible.

3 English

Image 3

Contents Table of Contents English Safety InformationImportant Safety Instruction Class B emissions limitsPrecautions Do not Usage Notice Eye Safety Warnings Package Overview IntroductionMain Unit Product OverviewConnection Ports Remote Control Coin Cell Battery Replacement Backup Remote ControlConnect to Computer/Notebook InstallationConnect to Video PlayStation 3 Games Connect to 3D Video Devices5 English Using the 3D glasses Powering On the Projector Powering On/Off the ProjectorPowering off the projector Adjusting the Projector’s Height Adjusting the Projected ImageAdjusting Projected Image Position Using PureShift  Adjusting the horizontal image position  PureShift Range Diagram Adjusting Projection Image SizeUser Controls Remote ControlThan From Hdmi 1 connectorFrom Hdmi 2 connector From VGA connectorOn-screen Display Menus How to operateMenu Tree Main Menu Sub Menu SettingsImage Display ModeColor ContrastBrightness SharpnessPureEngine Color SettingsNoise Reduction GammaPureEngine Demo PureDetailPureColor PureMotionColor Temperature Color GamutCMS Color Management System Use or to select from Normal, Red, Green or Blue channels RGB Gain/BiasColor Space RGB ChannelFormat DisplayKeystone ZoomEdge Mask Image Shift3D 2D 3D Mode3D Sync. Invert 3D FormatLamp Setting Menu LocationProjection 12V Trigger B Test PatternBackground Color 12V Trigger aUser Controls Lamp Reminder Lamp ModeLamp Reset Lamp HourHigh Altitude LanguageInput Source Source LockAuto Power Off SignalReset Image Problems TroubleshootingTwo images, side-by-side format Image has slanted sidesImage is reversed Blurry double imageProjector stops responding to all controls Other ProblemsRemote Control Problems If the remote control does not workLED Lighting Messages Message Power LED Temp LED Lamp LEDOn Screen Messages  Power down timer active  Lamp warning  Power offReplacing the Lamp Lamp Replacing Procedure  Computer Compatibility for PC Compatibility Modes Computer Compatibility for MAC SBS  3D Input Video CompatibilityRS232 Pin Assignments RS232 Commands and Protocol Function ListUART16550 Fifo RS232 Protocol Function ListSetup Ceiling Mount Installation Optoma Global Ofﬁces Japan DeutschlandScandinavia KoreaRemarque à l’intention des utilisateurs canadiens Regulation & Safety NoticesFCC Notice Operation ConditionsDisposal instructions Declaration of Conformity for EU countries