Optoma Technology XX152 N manual Auto Power Off, Signal, Reset

Page 42

User Controls

NOTE

“Signal” is not supported when the input source is HDMI.

NOTE

“IRE” is only sup- ported on NTSC signal.

Auto Power Off

Set the interval of power-off of the system, if there is no signal input. (In minutes).

Signal

For RGB/Component Source

Frequency: Change the display data frequency to match the frequency of your computer’s graphic card. Use this function only if the image appears to flicker vertically.

Phase: Synchronize the signal timing of the display with the graphic card. If the image appears to be unstable or flickers, use this function to correct it.

H Position: Adjust the image horizontal position.

V Position: Adjust the image vertical position.

Automatic: Automatically selects the signal. If you use this function, the Frequency and Phase items are grayed out, and if Signal is not automatic, the Frequency and Phase items will appear for user to manually tune and saved in settings after that for next time projector turns off and on again.

For Video Source:

White Level: Allow user adjust White Level when inputting SVideo or Video/CVBS signals.

Black Level: Allow user adjust Black Level when inputting S- Video or Video/CVBS signals.

Saturation: Adjust a video image from black and white to fully saturated color. Press the ◄ to decrease the amount of color in the image. Press the ► to increase the amount of color in the image.

Hue: Adjust the color balance of red and green. Press the ◄ to increase the amount of green in the image. Press the ► to increase the amount of red in the image.

IRE: Adjust measurement of composite video signals.

Reset

Return the adjustments and settings to factory default values.

Current: Reset current signal’s settings to factory default values.

All: Return the settings for all menus to factory default values.

English 42

Image 42
Contents Table of Contents Class B emissions limits Safety InformationImportant Safety Instruction EnglishPrecautions Do not Usage Notice Eye Safety Warnings Introduction Package OverviewProduct Overview Main UnitConnection Ports Remote Control Backup Remote Control Coin Cell Battery ReplacementInstallation Connect to Computer/NotebookConnect to Video Connect to 3D Video Devices PlayStation 3 Games5 English Using the 3D glasses Powering On/Off the Projector Powering On the ProjectorPowering off the projector Adjusting the Projected Image Adjusting the Projector’s HeightAdjusting Projected Image Position Using PureShift  Adjusting the horizontal image position Adjusting Projection Image Size  PureShift Range DiagramRemote Control User ControlsFrom VGA connector From Hdmi 1 connectorFrom Hdmi 2 connector ThanHow to operate On-screen Display MenusMain Menu Sub Menu Settings Menu TreeDisplay Mode ImageSharpness ContrastBrightness ColorGamma Color SettingsNoise Reduction PureEnginePureMotion PureDetailPureColor PureEngine DemoColor Temperature Color GamutCMS Color Management System RGB Channel RGB Gain/BiasColor Space Use or to select from Normal, Red, Green or Blue channelsDisplay FormatImage Shift ZoomEdge Mask Keystone3D Mode 3D 2D3D Format 3D Sync. InvertLamp Setting Menu LocationProjection 12V Trigger a Test PatternBackground Color 12V Trigger BUser Controls Lamp Hour Lamp ModeLamp Reset Lamp ReminderSource Lock LanguageInput Source High AltitudeAuto Power Off SignalReset Troubleshooting Image ProblemsBlurry double image Image has slanted sidesImage is reversed Two images, side-by-side formatIf the remote control does not work Other ProblemsRemote Control Problems Projector stops responding to all controlsMessage Power LED Temp LED Lamp LED LED Lighting Messages Power down timer active  Lamp warning  Power off On Screen MessagesReplacing the Lamp Lamp Replacing Procedure Compatibility Modes  Computer Compatibility for PC Computer Compatibility for MAC  3D Input Video Compatibility SBSRS232 Commands and Protocol Function List RS232 Pin AssignmentsRS232 Protocol Function List UART16550 FifoSetup Ceiling Mount Installation Optoma Global Offices Korea DeutschlandScandinavia JapanOperation Conditions Regulation & Safety NoticesFCC Notice Remarque à l’intention des utilisateurs canadiensDeclaration of Conformity for EU countries Disposal instructions