JVC GD-V4211PCE, GD-V4210PCE-G, GD-V4210PZW-G instruction manual Safety Precautions, FCC Notice

Page 2

Safety Precautions

FCC NOTICE

GD-V4210PZW / GD-V4210PZW-G / GD-V4210PCE / GD-V4210PCE-G

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

GD-V4211PCE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

EUROPE EMC STANDARD NOTICE

GD-V4210PZW / GD-V4210PZW-G / GD-V4210PCE / GD-V4210PCE-G

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measure.

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS

PRODUCT TO RAIN OR MOISTURE.

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service. Please read these “Important Safeguards” carefully before use.

All the safety and operating instructions should be read before the product is operated.

The safety and operating instructions should be retained for future reference.

All warnings on the product and in the operating instructions should be adhered to.

All operating instructions should be followed.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Do not use attachments not recommended by the product manufacturer as they may be hazardous.

Do not use this product near water. Do not use immediately after moving from a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards.

Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer.

2

Image 2
Contents Instructions Safety Precautions FCC NoticeEnglish Remote Control Parts IdentificationMonitor Front View Remote sensor/power lampSelf-diagnostic lamps Menu buttonMonitor Rear Views Audio input terminals pin jack RGB B input/output terminalsRGB a input terminal D-sub, 15-pin Component input terminals Video a terminalsVideo B terminals Preparations Checking the AccessoriesInstalling the Batteries When installing the Monitor on a stand InstallationPrecautions When mounting the Monitor on the wallComputer signals Preset and user-defined video modes Available SignalsVideo signals ConnectionsConnection Examples AV connections DVD player, etcBasic Operations Daily OperationsPress Aspect to select the screen size Precautions for using the screen mode switching functionChanging the Aspect Ratio AspectMenu Video AdjustmentsAdjusting the Picture Quality MENU/EXITTo reset the adjustments Adjusting the Screen Size and PositionTo make an adjustment while viewing the adjustment bar Contrast Bright Chroma Sharpness PhaseMonitor twice to exit from the menu Press 2/3 to adjust the selected itemPress MENU/EXIT or Menu on OperationsAdjusting the Color Temperature Adjusting the White BalanceBars GainChanging the Picture Mode Changing the Aspect RatioSetting the Receivable Signal Types Setting the RGB Input Other Convenient Functions Showing On-screen DisplayConfirm the hour of use Setting the Auto Sleep FunctionConfirming the Use Time Press 5/ to move the cursor 3 to Auto SleepPress 5/∞ to move the cursor 3 to Control Lock Press 2/3 to select the desired settingProhibiting the Monitor’s Button Operations Using the Pixel Shift Function Setting the High-Definition Signal TypesPress 5/∞ to move the cursor 3 to HD Signal Mode Mounting the Monitor VerticallyUsing the Power Save Function Refreshing the Screen Resetting All the Setup Menu SettingsPreventing the Afterimage Effect Resetting All the Menu Settings Press 5/∞ to move the cursor 3 to all reset on the secondSerial Connections and Operations Connecting the Remote Control CablesTurn on all the connected Monitors Press Mode Assigning ID NumbersOperating the Monitors Simultaneously Operating the Monitors IndividuallyMenu Classifications Main MenuSize Signal ModeBright Color TempSetup Menu Troubleshooting Sound does not occurYour Name Telephone No Address Specifications RGB B Options not suppliedRGB a AudioPin assignment Specifications for terminals Dimensions
Related manuals
Manual 4 pages 23.11 Kb