JVC GD-V4211PCE Confirming the Use Time, Confirm the hour of use, Setting the Auto Sleep Function

Confirming the Use Time

You can confirm the hours of use on the Setup Menu. This may be necessary when you ask for any service.

1 On the remote control:

Press MENU/EXIT while holding VOLUME – to display the Setup Menu.

On the Monitor:

Press MENU while holding 2 to display the Setup Menu.

S E T - U P M E N U	1 / 2
A U T O S L E E P	: 1 M I N .
C O N T R O L L O C K	: O N
S T A T U S D I S P L A Y	: O N
V E N T I L A T I O N M O D E : H
H D S I G N A L M O D E	: 1 0 8 0 i
W H I T E B A L A N C E

A D J U S T : S E L E C T : E X I T : M E N U

2 Keep pressing 5/° until the second page of the Setup Menu appears.

•The Setup Menu consists of two pages. If you keep pressing 5/°, you can move to the other page from the current page.

S E T - U P M E N U		2 / 2
P I X E L S H I F T		: O N
P O W E R S A V E		: O N
C O L O R - R E V E R S E		: O N
R E F R E S H		: O N
r e s e t
a l l r e s e t					Hours of use
H O U R M E T E R x 1 0 0 0 : 0 0 1
A D J U S T :	S E L E C T :		E X I T :
				M E N U

3 Confirm the hour of use.

•The displayed value for the hours of use is divided by 100. To calculate the actual hours of use, multiply the displayed value by 100.

4 Press MENU/EXIT (or MENU on the Monitor) once to exit from the menu operations.

Notes:

•The value for the hours of use is added by one hour unit. If you use the monitor within one hour, it will not be added to the hours of use.

•The period when the monitor is on standby (the power lamp glows orange) will not be added to the hours of use.

Setting the Auto Sleep Function

This function allows you to turn off (into standby mode) automatically when no signal comes in for a certain period of time.

•The power lamp flashes (orange) while in the Sleep mode (standby).

•When signals come in while in the Sleep mode, the Monitor turns on (the power lamp glows green).

1 On the remote control:

Press MENU/EXIT while holding VOLUME – to display the Setup Menu.

On the Monitor:

Press MENU while holding 2 to display the Setup Menu.

Cursor (3)	S E T - U P M E N U		1 / 2
	A U T O S L E E P		: 1 M I N .
	C O N T R O L L O C K		: O N
	S T A T U S D I S P L A Y		: O N
	V E N T I L A T I O N M O D E : H
	H D S I G N A L M O D E		: 1 0 8 0 i
	W H I T E B A L A N C E
	A D J U S T :	S E L E C T :		E X I T :
					M E N U

2 Press 5/° to move the cursor (3) to “AUTO SLEEP.”

•The Setup Menu consists of two pages. If you keep pressing 5/°, you can move to the other page from the current page.

3 Press 2/3 to select the desired amount of time.

Select the number of minutes before the Monitor goes into standby mode after the signal has ceased to be supplied.

Each time you press the button, the amount of time changes as follows:

OFF1 MIN.2 MIN.3 MIN.4 MIN.5 MIN.

To cancel the Auto Sleep function, select “OFF.”

4 Press MENU/EXIT (or MENU on the Monitor) once to exit from the menu operations.

ENGLISH

25