JVC DLA-M2000LU manual Remote Control Unit, For remote control only

Controls and Features

Controls and Features

Remote Control Unit

On the remote control, the same buttons as on the control panel of the projector are provided except for the following buttons. For the same buttons, operation is the same in principle.

For remote control only:

DIGITAL ZOOM +/-, QUICK ALIGN., FREEZE, ZOOM T/W, FOCUS +/-

Notes

•The ZOOM T/W buttons work only if the lens unit with a zooming function is used.

•The following buttons are not used with this projector.

VIC SELECT, SHIFT U/D, SHUTTER

4Cursor (5/∞/2/3) /ENTER button

When using this as the cursor button, press it in the 5/∞/ 2/3 directions to select menu items or adjust settings. When using it as the ENTER button, press the button straight down.

ENTER is used in the menu mode. Use to display the hierarchical menus. Also use when “ENTER” is displayed against the item on the menu screen or when the “All reset” selection is confirmed. For details, refer to “Basic Menu Operation” on page 42.

5 PC button

Use this button to select a device connected to the PC 1

or PC 2 terminals. Each time you press the button, the

qPRESET button

This PRESET button only works as a reset button for the direct button adjustment of the VOLUME button and KEYSTONE button of the control panel and the VOLUME button and DIGITAL ZOOM button of the remote control. When adjusting the volume, keystone or digital zoom (when the setting is displayed on the screen) the adjusted value is reset to that which was set when the projector was shipped from the factory. Of the menu items, this button only works for the keystone setting screen.

w FREEZE button

During projection of an image on the screen, press this

button to obtain a still picture.

To restore normal projection, press it again. (Refer to

No.51781

e

w q

p 9 8

FREEZEOPERATE

HIDE

PRESETMENU

	E
	NT
	E
	R
ESCAPE	VIC SELECT

PC

+

DIGITALZOOM KEYSTONE VIDEO

–

1

2

3

4

5

6

DIGITALVIDEO ZOOM

–

LENS

U T +

SHIFT ZOOM FOCUS

D W –

+	QUICK	+
SHUTTER	ALIGN.	VOLUME

––

r

t y

u

selection alternates between PC 1 and PC 2. (Refer to

page 32.)

* “PC 1” or “PC 2” will be displayed on the top right of the

projected image. (This function can be disabled using the

menu.)

6VIDEO button

Use this button to select a device such as a video deck connected to the AV IN terminal (VIDEO or Y/C input terminal) of the projector. Each time you press the button, the selection alternates between Y/C and VIDEO. (Refer to page 32.)

*“Y/C” or “VIDEO” will be displayed on the top right of the projected image. (This function can be disabled by the menu.)

7 Wired remote control terminal

To use the remote control as a wired unit, connect the

supplied remote cable between this terminal and the

page 36.)

* Depending on the video signal source (UXGA, etc.), this

button does not work.

eHIDE button

Use this button to turn off the image on the screen and audio sound temporarily. Pressing it again makes the image and audio sound to resume. (Refer to page 34.)

rFOCUS +/– buttons

Use these buttons to adjust the focus of the projected video image.

+: The focus point becomes more distant.

–: The focus point becomes nearer.

t VOLUME +/– buttons

Use these buttons to adjust the sound volume:

+ : Increase the volume level. (0 →	50)
– : Decrease the volume level. (50 →	0)

RM-M2000 REMOTE CONTROL UNIT

7

1Remote control’s signal transmitter

2OPERATE button

When the projector is in the stand-by mode, press this button one second or more, and the projector is turned on, causing the OPERATE indicator to light.

Press it one second or more again, and the projector goes into the cool-down mode, then stand-by mode. (Refer to page 31.)

*The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Use the button after approximately 1 minute.

Memo

While in the cool-down mode (STAND BY indicator is blinking):

Even if you press the OPERATE button, the projector is not turned on. Wait until the projector enters stand-by mode (STAND BY indicator stays lit).

3MENU button

Use this button to enter or exit the menu mode. The main menu appears or disappears at the screen. For details, refer to “Basic Menu Operation” on page 42.

REMOTE terminal on the back of the projector. (Refer to

page 20.)

* The remote control’s signal transmitter will stop working

when the cable is connected to this terminal.

8KEYSTONE / buttons

Use these buttons to correct a trapezoidal distortion of the projected image. (Refer to page 34.)

9DIGITAL ZOOM +/– buttons

A part of image can be magnified up to four times on the screen.

Each time the + or – button is pressed, the image is enlarged or the enlarged image is reduced by a certain degree. (Refer to page 36.)

*Images which are enlarged with the digital zoom become less clear.

*Depending on the video signal source (UXGA, etc.), this button does not work.

pESCAPE button

This button is used in the menu mode to return to the previous menu. When the main menu is displayed, this button will cause the menu to disappear. For details, refer to “Basic Menu Operation” on page 42.

(Refer to page 33.)

yQUICK ALIGN. (Quick Alignment) button Use this button to automatically align “Brightness”, “Contrast”, “Horizontal and vertical position”, “Tracking” and “Phase” for the projected image.

During the automatic alignment, “Quick Alignment” appears on the screen, and disappears after alignment is finished. (Refer to page 35.)

*The “Quick Alignment” function only works when the signal is input from the input terminal of either PC 1 or PC 2. It does not work when the signal is input from the VIDEO IN terminal (VIDEO or Y/C input terminal).

CAUTION

•Automatic alignment with the quick alignment function should be carried out on a bright still-picture. This function may not work correctly on a dark picture or motion-picture. If adjustment with this function is not satisfactory, adjust “Brightness”, “Contrast”, “Horizontal and vertical position”, “Tracking” and “Phase” in the menu mode.

uZOOM T/W buttons

Use these buttons to adjust the projected screen size. (They work only if the lens unit with a zooming function is used.)

T (Tele): The projected screen size decreases.

W (Wide): The projected screen size increases.

ENGLISH
DEUTSH
FRANÇ AIS
ITALIANO
ESPAÑOL	DLA- DLA-

1-11 12

13 M2000LE M2000LU