JVC DLA-M2000LU manual Replacing the Light-Source Lamp, Remove the lamp-replacement opening, Hours

Page 33

Replacing the Light-Source Lamp

The light-source lamp has a service life of approximately 1000 hours.

Replacing the Light-Source Lamp

■Be sure that the power cord is unplugged from the wall outlet.

When the light-source lamp approaches the end of its service life, degradation progresses rapidly.

The LAMP indicator and the message on the screen warn you that replacement of the lamp is required,

as follows:

1 Remove the lamp-replacement opening

Accumulated used hours of the light-source lamp

900 hours

1000 hours

•The LAMP indicator lights up on the projector.

•On the screen, “Lamp replacement” appears in red. To cancel this message, press the ESCAPE button.

•Arrange for a new light-source lamp or replace the light-

source lamp a little earlier.

* Every time the projector is turned on, the message appears.

•The LAMP indicator blinks on the projector.

•On the screen, “Warning Lamp replacement” appears in red and the word “Warning” blinks.

Replace the light-source lamp.

To cancel this message, press the ESCAPE button. However, the same message will appear every one hour.

*Only OPERATE button to stop the projector and the ESCAPE button are operative.

*Once the projector is turned off, the projector does not turn on unless the light-source lamp is replaced with new one.

Lamp replacement

ESCAPE

Warning

Lamp replacement

ESCAPE

cover by loosening screws.

Loosen the two screws with a flat-end screwdriver.

Screw

Note

•The screws are fitted so that they do not come off the lamp- replacement opening cover.

Lamp-replacement opening cover

No.51781

 

• The projector is forcibly shut off.

1010 hours

* The projector does not turn on unless the light-source lamp is

replaced with new one.

 

 

 

Purchase a new light-source lamps (Part No. : BHL5003-SU) from the authorized dealer where you purchased the projector, or consult the Service Center.

CAUTIONS

Be careful not to damage the claw.

2 Loosen the screws, raise the handle, and pull out the light-source lamp.

• If the projector is set up in a constricted place which is unsuitable for work, and if you perform replacement work there, this

could cause injury. Move the projector to a place large enough for work, and then replace the light-source lamp.

• Use a genuine product for the light-source lamp. If you use other than a genuine product, this could cause a malfunction.

Loosen the two screws with a flat-end screwdriver.

Note

Screw

1-33

Also, never use an old light-source lamp. This could cause marked degradation in performance or explode, possibly causing

the projector to malfunction or broken pieces to injure you.

• Do not replace the light-source lamp immediately after the projector has been used. The temperature of the light-source

lamp is still high and could cause a burn. Allow a cooling period of one hour or more before performing replacement.

• Before starting light-source lamp replacement work, turn off the MAIN POWER switch, and disconnect the power cord from

the wall outlet. If you perform the replacement work with the power cord connected, this could cause injury or electric shock.

• The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light-source

lamp. If anything is unclear, please consult your dealer.

56

• The screws are fitted so that they do not come off the light- source lamp.

Light-source lamp

Handle

(To be continued on the next page)

57

ESPAÑ OL ITALIANO FRANÇ AIS DEUTSH ENGLISH

DLA-M2000LU DLA-M2000LE

Page 32 Page 34
Image 33
Page 32 Page 34
Contents DLA-M2000LU Power cord Do not allow any unqualified person to install the unitContents DLA-M2000LE For United Kingdom For European Product should be placed more than one foot awayUnited Kingdom only How To Replace The FuseDo not cut off the main plug from this equipment This Apparatus Must be EarthedAA/R6-size dry cell battery Remote control unit RM-M2000GApprox m For checking operationControls and Features Front Side / Top Surface / Right SideLeft-hand Side / Rear Side Control Panel on the Projector Bottom SurfaceConnector Panel For remote control only Remote Control UnitInstalling the Projector Installing BatteriesPrecautions for Installation Adjusting the Inclination of the Projector Installing the Projector against the ScreenTrapezoidal-distortion correctable maximum angle Projection Distance and Screen Size Setting the Amount of Lens ShiftingSetting the Position Selecting Screw for Ceiling Mounting Effective Range and Distance of the Remote Control UnitWhen installing adjusting/setting the unit Using as a wireless remote control unitSignals that Can Be Input to the Projector Connecting to Various DevicesVideo signals Computer signalsConnecting to Hi-Vision Devices Connecting to Video DevicesBNC-RCA Video devicesConnecting to Devices which Control the Projector Connecting to Other DevicesGame device, etc Desktop typeConnecting to Computer Devices Connection to an IBM PC or IBM-compatible computerConnection to Macintosh Connecting the Power Cord Basic OperationsRemoving the Lens Cap Adjust Focus Adjusting Sound Volume Language displayAdjust the Screen Size Zooming Projector’s buttons Select the Input source to be ProjectedTurning off Image and Sound Hide Removing the Trapezoidal Distortion of the ImageQuick Alignment Function Quick Align Menu Transition Diagram in No signal Menu Mode Remote control unit Displaying a Still Picture FreezeQuick Reference Guide for No signal Menu Mode Menu OperationsQuick Reference Guide for Video Menu Mode Menu Transition Diagram in Video Menu ModeSubmenus in Video Menu Mode AUTO*/NTSC/NTSC4.43/PAL/SECAMMenu Transition Diagram in PC Menu Mode Quick Reference Guide for PC Menu ModeEnter Basic Menu Operation Changing the Color System Video Menu Mode Only Changing the Language DisplaySet the color system with the cursor button 5 or ∞ Adjusting Picture Quality Adjusting Tracking / PhaseAdjusting Color temperature Adjusting the Video Screen/Menu PositionVideo submenu Setting 1 submenu PC submenu Setting submenuChanging the Image Size Resize Function PC Menu Mode Only Changing the Image Tone/Aspect Ratio Video Menu Mode OnlyResize Resize PanelPC2 BNC RGB Setting and Adjusting Other Functions OptionsGetting Information Replacing the FuseSelect Information with the cursor button 5 or ∞ Projector and the wall outletReplacing the Light-Source Lamp Remove the lamp-replacement openingCover by loosening screws HoursTurn on the Main Power switch to go Into stand-by mode Resetting the Lamp Use TimeReset the lamp use time Insert the new light-source lamp fullyTroubleshooting Cleaning and Replacing the Filter CoverMaintenance When warning indication is shown by the blinking indicatorsAction to be taken for warning indication Stopping the projectorMessage Cause Corrective action Command Format Communication SpecificationsControl command table RS-232C external controlFor lens unit GL-M2910G AppendixFor lens unit GL-M2915SG For lens unit GL-M2920ZG 2 toProjector

DLA-M2000LU specifications

The JVC DLA-M2000LU is a cutting-edge projector that epitomizes the advancement in home theater technology. Designed with professional users in mind, the DLA-M2000LU delivers exceptional image quality, making it ideal for commercial venues, screening rooms, and high-end home theaters.

One of the standout features of the DLA-M2000LU is its native 4K resolution, which allows for breathtaking detail and clarity. With a resolution of 4096 x 2160 pixels, this projector excels at rendering intricate textures and vibrant colors with remarkable fidelity. The 4K output is complemented by JVC’s e-Shift technology, which enhances the quality of lower resolution content, upscaling it to near 4K quality. This feature ensures that every viewing experience, whether it’s a blockbuster movie or a sports event, is lifelike and immersive.

The DLA-M2000LU is equipped with JVC’s proprietary D-ILA (Direct-Drive Image Light Amplifier) technology. This innovative technology allows for deeper blacks and superior contrast ratios, providing a more dynamic picture. With a contrast ratio of 100,000:1, users can enjoy rich shadow details and bright highlights, enhancing the overall cinematic experience.

Color reproduction is further enhanced thanks to the projector’s wide color gamut. The DLA-M2000LU supports HDR (High Dynamic Range) content, allowing for a greater range of colors and luminance levels. This capability means that viewers can appreciate the subtleties of color in every scene, which is particularly important for filmmakers aiming to convey their artistic vision.

Another notable characteristic of the DLA-M2000LU is its robust connectivity options. The projector features multiple HDMI inputs, allowing for seamless integration with various media devices. Additionally, it supports various video formats, including DCI-P3, ensuring compatibility with today’s media standards.

In terms of installation, the JVC DLA-M2000LU offers a range of lens options, making it versatile for different room sizes and layouts. The motorized lens shift, zoom, and focus capabilities ensure that users can achieve the optimal screen position with ease.

With its stunning image quality, advanced technologies, and professional grade features, the JVC DLA-M2000LU stands as a premier choice for anyone seeking to enhance their visual experience. Whether it’s for a commercial application or a dedicated home cinema, this projector promises to deliver unparalleled performance and satisfaction.
Top Page Image Contents