JVC DLA-M2000LU manual Message Cause Corrective action

Warning Messages

The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take

the corrective action described here.

	Message		Cause	Corrective action	Page
		•	No device is connected to the	• Connect a device to the selected	9, 11,
			input terminal.	terminal.	24 ~ 29,
		•	The terminal is connected but no	• Operate the connected device	32
			signal is output from the	and output a signal.
	P C 1		connected device.
		*	The selected input mode (input
	N o i m a g e s i g n a l i s i n p u t t e d .
			terminal) name is shown in the
			first line of the massage.
		•	The frequency of the input video	• Input the video signals whose	22, 23,
			signal is out of range.	frequency is within the projector’s	66
		•	The selected input mode (input	specifications.
			terminal) name is shown in the
	P C 1		first line of the message.
	Frequency of image signal is out of range .
		•	Though the frequency of the input	• Input the video signals that	22, 23,
No			video signal is within the	satisfies the projector’s	66
			acceptable range, other items	specifications.
.			such as resolution are out of the
51781
	P C 1		projector’s specifications.
		•	The selected input mode (input
	N o i m a g e s i g n a l i s s h o w n f o r t h i s t y p e .
			terminal) name is shown in the
			first line of the message.
		•	When the FREEZE button is	• To release freezing, press the	13, 36
			pressed, this message appears	FREEZE button on the remote
			for a few seconds.	control.
		•	When a button not acceptable is
			pressed during freezing, this
	FREEZE		message appears for a few
			seconds to notify that the image is
			being frozen.
		•	When the FREEZE button is	• Freeze function does not work for	13, 36
			pressed for the video signals that	the inputted video signals.
			cannot be frozen (UXGA, etc.),	To use this function, input the
			this message appears for a few	video signals that can be frozen.
			seconds to notify that the image
	FREEZE		cannot be frozen.
		*	To forcibly clear the message,
			press the ESCAPE button.

1-37 64

Warning Messages

Message		Cause	Corrective action	Page
	•	When the DIGITAL ZOOM button	• Digital-zoom function does not	12, 36
		is pressed for the video signals	work for the inputted video
		that cannot be zoomed (UXGA,	signals.
		etc.), this message appears for a	To use the this function, input the
		few seconds to notify that the	video signals that can be digitally
D.ZOOM		image cannot be digitally zoomed.	zoomed.
	*	To forcibly clear the message,
		press the ESCAPE button.
	•	The accumulated lamp use time	• Press the ESCAPE button to	10, 12,
		reaches 900 hours.	clear the massage.	54 ,56
	*	Every time the projector is turned	(This display can be cleared with
		on, this message appears on the	the MENU button or other
		screen.	buttons.)
Lamp replacement			• Arrange for a new light-source
			lamp or replace the light-source
ESCAPE
			lamp a little earlier.
	•	The accumulated lamp use time	• Replace the light-source lamp	56 ~ 59
		reaches 1000 hours.	and reset the lamp use time.
		The word “Warning” blinks.
	*	The message can be cleared by
Warning		pressing the ESCAPE button.
Lamp replacement		However, the same message will
ESCAPE		appear every one hour.
	*	Once the projector is turned off,
		the projector does not turn on
		unless the light-source lamp is
		replaced with new one.
	*	When the accumulated lamp use
		time reaches 1010 hours, the
		projector is forcibly shut off.

Memo

The message display language corresponds to the menu display language setting. This is set to “English (English)” when the projector is bought. The display language can be selected from 6 languages. (Refer to page 45.) However, the input mode (PC1, PC2,Y/C, VIDEO) and button indications (FREEZE, D.ZOOM, ESCAPE) are only displayed in English irrespective of the display language setting.

The language settings in the section are explained in “English”.

65

ESPAÑ OL ITALIANO FRANÇ AIS DEUTSH ENGLISH

DLA-M2000LU DLA-M2000LE