JVC DLA-M2000LU manual Bottom Surface, Control Panel on the Projector

Controls and Features

Bottom Surface

y

u i

o

y Air inlet (filter)

	Air is taken in through the filter to cool the light-source
	lamp. If the filter is blocked or if something that obstructs
	the flow of air is placed around the projector, heat may
No.	build up inside and could cause a fire. For required
	space, refer to “Precautions for Installation” on page 15.
	CAUTION
51781
	• Be careful as paper, cloth or soft cushion could be drawn in
	if placed nearby. Do not block the filter, or heat may build
	up and could cause a fire.
	• Clean the filter periodically. For details, refer to “Cleaning
	and Replacing the Filter Cover” on page 60. Deposition of
	dirt on the filter reduces the cooling effect, causing heat to
	build up inside, which could cause a fire or malfunction.

Controls and Features

Control Panel on the Projector
	t		1
	r
	e		STAND BY	2
		LAMP TEMP
			OPERATE
	w	HIDE		3
	q		PC	4
		KEYSTONE	VOLUME	5
			VIDEO
		PRESET	MENU
	p			6
	9			7
	8	ESCAPE	ENTER
1	STAND BY Indicator	Memo

ON : When in stand-by mode.

While in the cool-down mode (STAND BY indicator is blinking):

Blinking: When in cool-down mode.

Even if you press the OPERATE button, the projector is not

Memoturned on. Wait until the projector enters stand-by mode (STAND BY indicator stays lit).

About the cool-down mode:

This projector has a function to cool down the heated lamp for a	4	PC button
fixed period of time (approx. 120 seconds) after projection is		Use this button to select a device connected to the PC 1
finished. This feature is referred to as the cool-down mode.		or PC 2 terminals. Each time you press the button, the
The purpose of the cool-down mode is to prevent inner parts		selection alternates between PC 1 and PC 2.
from being deformed or broken by heat from the heated lamp		* “PC1” or “PC2” will be displayed on the top right of the
as well as to prolong the life of the lamp.		projected image. (This function can be disabled by the
		menu.)
CAUTIONS	5	VIDEO button

ENGLISH

u Opening for replacing the light-source lamp

For replacing the light-source lamp, refer to “Replacing

the Light-Source Lamp” on page 56.

i Fixing foot

o Position selecting screw for ceiling mounting

When using the projector in an upside-down, ceiling-

mounted position (inverted top-to-bottom and right-to-

left), the “position selecting screw for ceiling mounting”

must be turned to switch to ceiling mounting.

This will correct variance in color images (shading),

which otherwise would occur in ceiling mounting.

For more information, refer to “Setting the Position

Selecting Screw for Ceiling Mounting” on page 21.

CAUTION

•To ceiling-mount and adjust the projector, special expertise and technique are necessary. Be sure to ask your dealer or specialist to perform this work.

•Do not turn off the MAIN POWER switch while in the cool- down mode.

•Do not place the projector on its side or stand it upright while in the cool-down mode; this may block the vents.

2OPERATE indicator

ON : When the projector is in operation (projecting).

OFF : When the projector is not in operation (not projecting).

3OPERATE button

When the projector is in the stand-by mode, press this button one second or more, and the projector is turned on, causing the OPERATE indicator to light.

Press it one second or more again, and the projector goes into the cool-down mode, then stand-by mode. (Refer to page 31.)

*You cannot use the OPERATE button for about one minute after the lamp blinks. Press the button after a minute or longer has elapsed.

Use this button to select a device such as a video deck connected to the AV IN (Y/C or VIDEO) terminal of the projector. Each time you press the button, the selection alternates between Y/C and VIDEO.

*“Y/C” or “VIDEO” will be displayed on the top right of the projected image. (This function can be disabled by the menu.)

6MENU button

Use this button to enter or exit the menu mode. The main menu appears or disappears at the screen. For details, refer to “Basic Menu Operation” on page 42.

7ENTER button

This button will be used in the menu mode. Use to display the hierarchical menus. Also use when “ENTER” is displayed against the item on the menu screen or when the “All reset” selection is confirmed. For details, refer to “Basic Menu Operation” on page 42.

8Cursor buttons 5/∞/2/3

These buttons will be used in the menu mode to select an item, or to set or adjust the value. For details, refer to “Basic Menu Operation” on page 42.

ESPAÑ OL ITALIANO FRANÇ AIS DEUTSH

DLA- DLA-

8

1-9

9

M2000LU M2000LE