No.51781
WARNING :
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION :
To reduce the risk of electric shock, do not remove cover. Refer servicing to qualified service personnel.
This projector is equipped with a 3-blade grounding- type plug to satisfy FCC rule. If you are unable to insert the plug into the outlet, contact your electrician.
FCC INFORMATION (U.S.A. only)
CAUTION: Changes or modification not approved by JVC could void the user’s authority to operate the equipment.
NOTE:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
About burning-in of the D-ILA device
Do not allow the same still picture to be projected for a long time or an abnormally bright video picture to be projected. Do not project video images with high-intensity or high- contrast on a screen. The video image could be burned in to the D-ILA device.
Use special care when projecting video games or computer program images. There is no problem with ordinary video-cassette playback images.
About the installation place
Do not install the projector in a place that cannot support its weight securely.
If the installation place is not sturdy enough, the projector could fall or overturn, possibly causing personal injury.
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In
order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, use and service. Please read these “Important Safeguards” carefully before use.
–All the safety and operating instructions should be read before the product is operated.
–The safety and operating instructions should be retained for future reference.
–All warnings on the product and in the operating instructions should be adhered to.
–All operating instructions should be followed.
–Place the projector near a wall outlet where the plug can be easily unplugged.
–Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
–Do not use attachments not recommended by the product manufacturer as they may be hazardous.
–Do not use this product near water. Do not use immediately after moving from a low temperature to high temperature, as this causes condensation, which may result in fire, electric shock, or other hazards.
–Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. The product should be mounted according to the manufacturer’s instructions, and should use a mount recommended by the manufacturer.
–When the product is used on a cart, care
should be taken to avoid quick stops, excessive force, and uneven surfaces which may cause the product and cart to overturn, damaging equipment or causing possible injury to the operator.
–Slots and openings in the cabinet are provided for ventilation. These ensure reliable operation of the product and protect it from overheating. These openings must not be blocked or covered. (The openings should never be blocked by placing the product on bed, sofa, rug, or similar surface. It should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.)
For proper ventilation, separate the product from other equipment, which may prevent ventilation and keep / distance more than 23-5/8" (60 cm).
electrician to install the proper outlet. Do not defeat the |
safety purpose of the grounded plug. |
– Power-supply cords should be routed so that they are not |
likely to be walked on or pinched by items placed upon or |
against them. Pay particular attention to cords at doors, |
plugs, receptacles, and the point where they exit from the |
product. |
– For added protection of this product during a lightning |
storm, or when it is left unattended and unused for long |
periods of time, unplug it from the wall outlet and |
disconnect the cable system. This will prevent damage |
to the product due to lightning and power line surges. |
– Do not overload wall outlets, extension cords, or |
convenience receptacles on other equipment as this can |
result in a risk of fire or electric shock. |
– Never push objects of any kind into this product through |
openings as they may touch dangerous voltage points or |
short out parts that could result in a fire or electric shock. |
Never spill liquid of any kind on the product. |
– Do not attempt to service this product yourself as |
opening or removing covers may expose you to |
dangerous voltages and other hazards. Refer all service |
to qualified service personnel. |
– Unplug this product from the wall outlet and refer service |
to qualified service personnel under the following |
conditions: |
a) When the power supply cord or plug is damaged. |
b) If liquid has been spilled, or objects have fallen on the |
product. |
c) If the product has been exposed to rain or water. |
d) If the product does not operate normally by following |
the operating instructions. Adjust only those controls |
that are covered by the Operation Manual, as an |
improper adjustment of controls may result in damage |
and will often require extensive work by a qualified |
technician to restore the product to normal operation. |
e) If the product has been dropped or damaged in any |
way. |
f ) When the product exhibits a distinct change in performance – this indicates a need for service.
–When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or with same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
–Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
–The product should be placed more than one foot away from heat sources such as radiators, heat registers, stoves, and other products (including amplifiers) that produce heat.
lamp is turned on. Exposure of your eyes to the strong |
light can result in impaired eyesight. |
– Do not look into the inside of this unit through vents |
(ventilation holes), etc. Do not look at the illumination |
lamp directly by opening the cabinet while the |
illumination lamp is turned on. The illumination lamp also |
contains ultraviolet rays and the light is so powerful that |
your eyesight can be impaired. |
– Do not drop, hit, or damage the light-source lamp (lamp |
unit) in any way. It may cause the light-source lamp to |
break and lead to injuries. Do not use a damaged light- |
source lamp. If the light-source lamp is broken, ask your |
dealer to repair it. Fragments from a broken light-source |
lamp may cause injures. |
– Xenon gas is enclosed with high pressure inside the light- |
source lamp (lamp unit) of this projector. If you drop or |
impart a shock to the lamp, or discard it as is, there is the |
possibility of explosion, leading to personal injury. Use |
special care when handling the lamp. For any unclear |
points, consult your product dealer. |
– Do not “ceiling-mount” the projector to a place which |
tends to vibrate; otherwise, the attaching fixture of the |
projector could be broken by the vibration, possibly |
causing it to fall or overturn, which could lead to personal |
injury. |
– Use only the accessory cord designed for this product to |
prevent shock. |
The power supply voltage rating of this product is |
AC 120 V, the power cord attached conforms to the |
following power supply voltage. Use only the power cord |
designated by our dealer to ensure Safety and EMC. |
When it is used by other power supply voltage, power |
cable must be changed. |
Ensure that the power cable used for the projector is the |
correct type for the AC outlet in your country. |
Consult your product dealer. |
Power cord
Power supply voltage: AC 120 V
*DO NOT allow any unqualified person to install the unit.
Be sure to ask your dealer to install the unit (eg. attaching it to the ceilling) since special technical knowledge and skills are required for installation.
If installation is performed by an unqualified person, it may cause personal injury or electrical shock.
