JVC DLA-M4000LU Basic Operations, When Turning On the Devices Connected to the Projector

Page 13

No.51666

Connecting to Various Devices (Cont.)

When Turning On the Devices Connected to the Projector

Turn on the switches of the projector and the devices connected in the following order.

Skip over unconnected devices if there is any.

Power switch of the monitor of the computer which provides input to the projector

Peripheral devices of the computer which provides input to the projector (Hard disk, magneto optical disk, scanner, etc.)

Power switch of AV devices which provide input to the projector

Projector itself

Power switches of devices to which the projector provides output

(AV devices and display monitor)

Power switch of the computer which provides input to the projector

* When turning off the power switches, do so in the reverse order.

CAUTIONS and NOTES

Do not turn off the MAIN POWER switch suddenly while the projector is being used or immediately after it has been used. This could cause a malfunction.

•Since the projector uses a high-intensity lamp and is heated to high temperature, cooling fans are operating even during projection. So, after use, the cooling fans continue to run until the light-source lamp is sufficiently cooled down after the OPERATE button was pressed. During the cooling-down, never turn off the main power switch. Turn it off only after the cooling fans (except the one for the light-source lamp power supply) have stopped running.

(The cooling fans will run for about 10 minutes after the STAND BY indicator has changed from flashing (for about 20 seconds) to steady lighting.)

•If you press the OPERATE button immediately after the light-source lamp lights, it takes about 30 seconds for the lamp to go off. To turn the lamp on again, wait 20 seconds or more before pressing the OPERATE button.

When the TEMP indicator lights, the power turns off automatically.

•While the light-source lamp is on, if an abnormal temperature rise is detected, the TEMP indicator comes on, the power is automatically cut off, and the projector’s EMERGENCY indicator blinks (goes into an emergency mode).

When the EMERGENCY indicator blinks, turn off the main power switch after the fans have stopped running.

•If the following abnormality occur to the projector, it goes into an emergency mode (the EMERGENCY indicator blinks). When the projector goes into an emergency mode, it stops projecting automatically and the cooling fans will continue to run for about 10 minutes more before they stop (except the cooling fan for the light-source lamp power supply which continues running as long as the MAIN POWER switch is on).

–When the fans stop running.

–When the temperature inside rises abnormally high.

•When the projector goes into an emergency mode:

After the fans have stopped, turn off the MAIN POWER switch and pull out the power cord. After that, re-insert the power cord and try to operate the projector. If it goes into emergency again, after the fans have stopped, turn off the main power switch, pull out the power cord, and consult your authorized dealer or service center for repair.

24

Basic Operations

■Projector’s buttons

STAND BY indicator

OPERATE indicator

TEMP

STAND BY

OPERATE LAMP

EMERGENCY AV

RGB

OPERATE button 2, 1

MAIN POWER switch 1, 2

■Remote control unit

QUICK

 

 

ALIGN.

OPERATE

OPERATE button

 

AV HIDE

PRESET

PAGE BACK

2, 1

LENS LOCK

N

 

 

M

 

 

EN

 

 

U/

 

UNLOCK

E

 

T

 

 

E

 

 

R

 

AV RGB/COMPUTER

U T +

SHIFT ZOOM FOCUS

D W –

LENS

The following describes the basic procedure for normal use of the projector.

1.Turning on the Power

1 Turn on the MAIN POWER switch of the projector.

ON [ ❙ ]:The main power turns on and the STAND BY indicator comes on.

Projector’s indicator

STAND BY

2Press the OPERATE button for one second or more.

(Or press the remote control’s OPERATE button for one second or more.)

•The OPERATE indicator comes on.

•About 30 seconds after the MAIN POWER switch is turned on, you can start projecting.

Remote control unit

Projector

OPERATE

or

OPERATE

Note

•After the power is turned on, the screen may be jumbled for a few seconds, but this is not a malfunction.

■Turning off the Power

1Press the OPERATE button for one second or more.

(Or press the remote control’s OPERATE button for one second or more.)

•The STAND BY indicator changes to blinking, and the projector goes into cool-down mode.

Example of the projector’s button

Projector

\

STAND BY

OPERATE

2Turn off the MAIN POWER switch after the cooling fans have

stopped running.

OFF [‡]: The MAIN POWER switch turns off and the STAND BY indicator goes off.

Projector

STAND BY

*Do not turn off the MAIN POWER switch during cool down mode (the STAND BY indicator blinking). About 10 minutes after the STAND BY indicator comes on steady (stand-by mode), the cooling fans (except the one for the light-source lamp power supply) will stop, and then turn off the MAIN POWER switch.

25

DLA-M4000LU DLA-M4000LE

Page 12 Page 14
Image 13
Page 12 Page 14
Contents For customer Use OperatingLamp directly by opening the cabinet while the illumination About burning-in of the D-ILA deviceContents Accessories Controls and Features Controls and FeaturesFront Side / Top Surface / Right Side Left-hand side / Back SideControl Panel Remote Control Unit Connector PanelInstall the batteries Installing BatteriesMenu / Enter Menu Operation Button Open the back coverPrecautions for Installation Installing the ProjectorInstalling the Projector Relationship relative to Glass SurfaceChange of projection screen according Lens Shift FunctionTo aspect ratio ScreenSignals that Can Be Input to the Projector Connecting to Various DevicesAdjustable range of the lens Projection Distances and Screen SizesDesktop type Example of a basic systemRGB output devices Connecting the Power Cord Supplied Connecting to Devices which Control the ProjectorPower cord into a wall outlet, Insert the plug of the suppliedTurning on the Power When Turning On the Devices Connected to the ProjectorTurning off the Power Basic OperationsAdjust focus Adjust the screen sizeFor Operating Other Functions Basic OperationsTo use the remote control’s Preset button To display the Setting menuProjector’s button To display Channel on the screenMaking Basic Settings Operating the Setting Menu Operating the Main MenuPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Basic Operation of the Main Menu Configuration of the Main Menu Computer-related inputChanging the Language Display Changing the Color SystemPress MENU/ENTER toward the 5 or ∞ mark to select Decoder Press MENU/ENTER toward the 2 or 3 mark to setAdjusting the Screen Position Adjusting the Pixel ClockAdjustment item Button Adjustment content To return to the main menu, pressSubmenu items Adjusting Picture QualityFollowing optional functions can be set adjusted Setting and Adjusting Other Functions OptionsAbout the lamp use time Picture menuDisplay, the video image resolution becomes coarse Adjustment item ButtonOptions menu Press MENU/ENTER to set fix Changing Setting the SourcePress the MENU/ENTER button Submenu Press the MENU/ENTER button to set Setting Up ChannelsPress MENU/ENTER to set Setting Up Channels Source setup Setting Up Channels Line setupChannel setup selection menu When Line is selectedWhen a switcher number SWNo is selected Setting Up Channels SWNo. setupPress the page Back button to set Changing Channels CH Change Setting Up or Changing User Sources Setting Up or Changing the Display Size Remote control unit Press the MENU/ENTER button to setMark to select a submenu item Remove the filter cover screws Cleaning and Replacing the FilterRemove the filters To return to the main menu, press page BACK. To finishClean the filters TroubleshootingReinstall the filters About Light-Source Lamp ReplacementTroubleshooting When the emergency indicator starts blinkingSpecifications SpecificationsEXT. in AV in input RGB in RGB inputDTV-format signals Victor Company of JAPAN, Limited DLA-M4000LE InstructionsImportant Information Improper adjustment of controls may result in damageContents Controls and Features On When the projector is in operation projecting On When in stand-by mode Blinking When in cool-down modeTemp indicator Input of external sync signals is automatically detected 51666 305 mm 600 mm 11.392 Type
Related manuals
Manual 68 pages 40.21 Kb
Top Page Image Contents