JVC DLA-M4000LU On When in stand-by mode Blinking When in cool-down mode, Temp indicator

Page 39

Controls and Features (cont.)

Control Panel

1 2

3

4 5 6

7

8

9

p

 

 

TEMP

 

RGB

SETTING

QUICK

STAND BY

OPERATE LAMP EMERGENCY AV

 

 

 

 

 

 

ALIGN.

Controls and Features (cont.)

Control Panel (Cont.)

1 2

3

4 5 6

7

8

9

p

 

 

TEMP

 

RGB

SETTING

QUICK

STAND BY

OPERATE LAMP EMERGENCY AV

 

 

 

 

 

 

ALIGN.

No.51666

1STAND BY Indicator

ON : When in stand-by mode.

Blinking : When in cool-down mode.

CAUTION

•The cool-down mode continues for about 20 seconds, during which projection cannot be started again. After the cooling- down period, the projector goes into stand-by mode, but the cooling fans will continue to run for about 10 minutes more.

•The purpose of the cool-down mode is to prevent inner parts from being deformed or broken by heat from the heated lamp as well as to prolong the life of the lamp. Do not turn off the main power switch while in the cool-down mode. Also, do not block any of exhaust openings while in cool-down mode.

2OPERATE indicator

ON: When the projector is in operation (projecting)

6EMERGENCY indicator

Blinking: Something abnormal has occurred with the projector.

Memo

About the emergency mode:

The emergency mode is shown when the following anomalies have occurred with the projector (the EMERGENCY indicator blinks). In the emergency mode, projection is automatically interrupted and the cooling fans operate for about 20 seconds.

•When the filter is clogged.

•When the light-source lamp has suddenly gone off.

•When the fans have stopped.

•When the temperature inside has risen abnormally high.

CAUTION

• When an emergency mode is shown:

After the cooling fans have stopped, turn off the main power switch and unplug the power cord from the wall outlet.

7AV button

Use this button to select a device such as a video deck connected to the EXT. IN terminal of the projector. Each time you press the button, the device selected changes as follows:

**

*Y/C and VIDEO can be used only when a video board separately sold has been installed.

8RGB button

Use this button to select a device connected to the RGB -1 or -2 terminals. Each time you press the button, the selection changes as follows:

pQUICK ALIGN. button

While a menu screen is shown, use this button to adjust

the values for the item selected. When no menu is shown, the quick alignment function works.

•When a menu is shown

button: The value for the selected item increases.

button: The value for the selected item decreases.

• When no menu is shown

Press the button and button at the same time:

QUICK ALIGNMENT is displayed on the screen and the quick alignment function works (TRACKING, PHASE, H. POS. and V. POS. are automatically adjusted). When the adjustment is finished, the display goes off automatically.

Memo

The quick alignment function :

•Works for computer input (RGB- 1 and - 2 input terminals) signals.

•Does not work for video input (EXT. IN input terminal) signals.

3OPERATE button

When the projector is in the stand-by mode, press this button for one or more seconds, and the main power switch is turned on, causing the OPERATE indicator to light. Press it again, and the projector goes into the cool-down mode, then stand-by mode.

Memo

While in the cool-down mode:

If you press the OPERATE button, the projector is not tuned on.

Check that the filter covers are correctly installed. Then, plug in the power cord again and try operating the projector.

If it goes into an emergency mode again, after the cooling fans have stopped, turn off the main power switch, unplug the power cord, and call your dealer for repair.

9SETTING button

Use this button to call up the setting menu. For details, refer to “Making Basic Settings” on page 30.

CAUTION

•Automatic adjustment with the quick alignment function should be done on a bright still-picture screen. This function may not work correctly on a dark screen or motion-picture screen. If adjustment with this function is not satisfactory, adjust TRACKING, PHASE, H. POS. and V. POS. manually (see pages 30, 36 and 37).

4Lamp indicator

ON : After the light-source lamp has been used for more than approx. 900 hours.

Blinking : Replace the lamp.(Ask the dealer where you purchased your projector to replace the lamp.)

5TEMP indicator

ON: The temperature inside the projector has abnormally risen.

Note

•While the TEMP indicator is on (during abnormal temperature), the power is automatically cut off, and an emergency mode is shown (with the EMERGENCY indicator blinking).

8

9

DLA-M4000LU DLA-M4000LE

Page 38 Page 40
Image 39
Page 38 Page 40
Contents For customer Use OperatingLamp directly by opening the cabinet while the illumination About burning-in of the D-ILA deviceContents Accessories Left-hand side / Back Side Controls and FeaturesControls and Features Front Side / Top Surface / Right SideControl Panel Remote Control Unit Connector PanelOpen the back cover Installing BatteriesInstall the batteries Menu / Enter Menu Operation ButtonRelationship relative to Glass Surface Installing the ProjectorPrecautions for Installation Installing the ProjectorScreen Lens Shift FunctionChange of projection screen according To aspect ratioProjection Distances and Screen Sizes Connecting to Various DevicesSignals that Can Be Input to the Projector Adjustable range of the lensExample of a basic system Desktop typeRGB output devices Insert the plug of the supplied Connecting to Devices which Control the ProjectorConnecting the Power Cord Supplied Power cord into a wall outlet,Basic Operations When Turning On the Devices Connected to the ProjectorTurning on the Power Turning off the PowerBasic Operations Adjust the screen sizeAdjust focus For Operating Other FunctionsTo display Channel on the screen To display the Setting menuTo use the remote control’s Preset button Projector’s buttonPress the Setting button to select the desired item Operating the Setting Menu Operating the Main MenuMaking Basic Settings Press the Setting button of the projectorOperating the Main Menu Basic Operation of the Main Menu Configuration of the Main Menu Computer-related inputPress MENU/ENTER toward the 2 or 3 mark to set Changing the Color SystemChanging the Language Display Press MENU/ENTER toward the 5 or ∞ mark to select DecoderTo return to the main menu, press Adjusting the Pixel ClockAdjusting the Screen Position Adjustment item Button Adjustment contentSubmenu items Adjusting Picture QualityPicture menu Setting and Adjusting Other Functions OptionsFollowing optional functions can be set adjusted About the lamp use timeAdjustment item Button Display, the video image resolution becomes coarseOptions menu Changing Setting the Source Press MENU/ENTER to set fixPress the MENU/ENTER button Submenu Setting Up Channels Press the MENU/ENTER button to setPress MENU/ENTER to set When Line is selected Setting Up Channels Line setupSetting Up Channels Source setup Channel setup selection menuSetting Up Channels SWNo. setup When a switcher number SWNo is selectedPress the page Back button to set Changing Channels CH Change Setting Up or Changing User Sources Remote control unit Press the MENU/ENTER button to set Setting Up or Changing the Display SizeMark to select a submenu item To return to the main menu, press page BACK. To finish Cleaning and Replacing the FilterRemove the filter cover screws Remove the filtersAbout Light-Source Lamp Replacement TroubleshootingClean the filters Reinstall the filtersTroubleshooting When the emergency indicator starts blinkingRGB in RGB input SpecificationsSpecifications EXT. in AV in inputDTV-format signals Victor Company of JAPAN, Limited DLA-M4000LE InstructionsImportant Information Improper adjustment of controls may result in damageContents Controls and Features On When in stand-by mode Blinking When in cool-down mode On When the projector is in operation projectingTemp indicator Input of external sync signals is automatically detected 51666 305 mm 600 mm 11.392 Type
Related manuals
Manual 68 pages 40.21 Kb
Top Page Image Contents