JVC DLA-M4000LU operating instructions Options menu, Adjustment item Button

Operating the Main Menu (Cont.)

Setting and Adjusting Other Functions (OPTIONS) (Cont.)

Operating the Main Menu (Cont.)

Setting and Adjusting Other Functions (OPTIONS) (Cont.)

DLA-M4000LU DLA-M4000LE

No.51666

■Remote control unit

QUICK
ALIGN.	OPERATE
	AV HIDE
PRESET	PAGE BACK
LENS LOCK	PAGE BACK button
	N
	M
	EN
	U/
UNLOCK	E
	T
	E
	R
	MENU/ENTER button

AV RGB/COMPUTER

U T +

SHIFT ZOOM FOCUS

D W –

LENS

■Submenu items

[OPTIONS menu]

O P T I O N S

5 Press MENU/ENTER toward the 2 or 3 mark to select an item to set (adjust).

• To adjust multiple items, repeat steps 4 and 5.

Adjustment item	Button			Adjustment content
		Sets whether to clear the menu display
		automatically a fixed time later or not.
		(Factory setting : NO)
MENU AUTO	2/3	YES: Clears the display automatically in
OFF			about 25 seconds.
		NO : Does not clear the display
			automatically.
		NO			YES
		Sets whether to show the line display (Y/C,
		VIDEO, etc.) at the top of the projected
		screen or not. (Factory setting : ON)
LINE DISPLAY	2/3	OFF: Does not show the line display.
		ON : Shows the line display.
			(The line display disappears about 5
			seconds after it is shown.)
		OFF			ON
		Reverses video image right-to-left.
RIGHT LEFT		(Factory setting : OFF)
	2/3 OFF: For the front method
REV.
		ON : For upside hanging from the ceiling
		OFF			ON
		Inversus video image upside-down.
TOP BOTTOM		(Factory setting : OFF)
	2/3 OFF: For normal set-up
INV.
		ON : For upside hanging from the ceiling
		OFF			ON
		Sets the clamp pulse’s position at the back
		porch (BP) or on the sink tip (ST).
		Normally, the clamp is used at BP. If, with
		some PCs or workstations, the screen
		becomes unstable such as being too dark
CLAMP	2/3	or too bright, try to switch to ST.
		(factory setting: BP)
		BP : The clamp pulse is positioned at the

■Remote control unit

QUICK
ALIGN.	OPERATE
	AV HIDE
PRESET	PAGE BACK
LENS LOCK	PAGE BACK button
	N
	M
	EN
	U/
UNLOCK	E
	T
	E
	R
	MENU/ENTER button

AV RGB/COMPUTER

U T +

SHIFT ZOOM FOCUS

D W –

LENS

■Submenu items

[OPTIONS menu]

O P T I O N S

Adjustment item	Button			Adjustment content
		Sets background color when there is no input
		signal. (Factory setting : BLUE)
BACK COLOR	2/3	BLUE			CYAN		BLACK		GREEN
		YELLOW				RED		MAGENTA
		Sets the color temperature of the video image
		being projected. Make adjustment when the
		image becomes reddish or bluish. (Factory
		setting : MIDDLE)
		LOW : Color temperature decreases
COLOR	2/3			(video image becoming reddish).
TEMP.		MIDDLE : Results in middle color
				temperature.
		HIGH : Color temperature increases
				(video image becoming bluish).
			LOW			MIDDLE		HIGH
		Sets the vertical-to-horizontal ratio (4 : 3 or 16

:9) of the video image projected. (Factory setting : 4 : 3)

4 : 3 : The aspect ratio of the screen

ASPECT	2/3		becomes 4 : 3. Set it to 4 : 3 for video
CHANGE			of NTSC, NTSC4.43, PAL, SECAM.
		16 : 9: The aspect ratio of the screen
			becomes 16 : 9. Set it to 16 : 9 for Hi-
			Vision devices (W-VHS VCR, etc.)
		4 : 3			16 : 9
		Sets the length of sleep time which
		automatically brings the projector into stand-
		by state. You can select one of the following
SLEEP TIME	2/3	sleep times : 10 minutes, 20 minute, 30
		minutes, 60 minutes and 0. (Factory setting :
		0 minutes)
		10		20		30	60	0
		If set to “0” minutes, this function does not work.

M E N U A U T O O F F	N O
L I N E D I S P L A Y	O N
R I G H T L E F T R E V .	O F F
T O P B O T T O M I N V .	O F F
C L A M P	B P
R E S I Z E	O N
B A C K C O L O R	B L U E
C O L O R T E M P .	M I D D L E
A S P E C T C H A N G E	4 : 3
S L E E P T I M E	0	M i n .
L A M P T I M E	1 0 H .

	back porch.
ST : The clamp pulse is positioned on the
	sink tip.
BP		ST
When the number of pixels (resolution)
sought by the input video is smaller than
that (resolution) of D-ILA device, the video
image is then enlarged to virtually full

M E N U A U T O O F F	N O		¶ To return to the main menu, press the PAGE
L I N E D I S P L A Y	O N
R I G H T L E F T R E V .	O F F		BACK button. To finish the main menu, press
T O P B O T T O M I N V .	O F F
C L A M P	B P		PAGE BACK again.
R E S I Z E	O N
B A C K C O L O R	B L U E		• To finish the menu display from the submenu display (OPTIONS
C O L O R T E M P .	M I D D L E
			menu), press PAGE BACK twice.
A S P E C T C H A N G E	4 : 3
S L E E P T I M E	0	M i n .
L A M P T I M E	1 0 H .

Notes

•The selected item is shown in magenta color. Items shown in gray color cannot be operated or set in the current mode.

•Items to be set (adjusted) are different when AV signals are input and when computer-system signals are input.

•When you turn the RESIZE function ON, allowing the screen to be enlarged virtually to its full size for projection (resizing

display), the video image (resolution) becomes coarse.

	screen size of D-ILA device and projected
	(resizing display). (Factory setting : ON)
	Does not work (cannot be set) for video
	system input.
	OFF : Does not enlarge the video image for
RESIZE	2/3	projection. When the number of
		pixels sought by video image is
		smaller than that of D-ILA device,
		projection takes place on a small
		screen size with a black area around
		the screen.
	ON : Enlarges virtually to the full screen
		size of D-ILA device for projection
		(resizing display).
	OFF		ON

Notes

•The selected item is shown in magenta color. Items shown in gray color cannot be operated or set in the current mode.

•Items to be set (adjusted) are different when AV signals are input and when computer-system signals are input.

Note

•When you view a conventional (normal) 4 : 3 video picture, which is not wide video picture, on the projector’s screen the aspect change function, the upper and lower parts of the video picture become partially invisible. View such an original video picture in 4 : 3 mode, respecting the producer’s intention.

(To be continued on the next page)

42 43