JVC DLA-M4000LU operating instructions Configuration of the Main Menu Computer-related input

Page 17

Operating the Main Menu (Cont.)

Configuration of the Main Menu (Computer-related input)

Operating the Main Menu (Cont.)

Operating the Main Menu (Basic Operation of the Main Menu)

Main menu (Computer-related inputs : During COMPUTER IN-1 or -2 input signal)

■Remote control unit

For projector’s menus, the setting menu and the main menu are available.

PIXEL CLOCK

POSITION

PICTURE

TRACKING

: The lateral size and display area of video image are adjusted.

PHASE

: Flickering or dim video image is adjusted.

V. POS.

: The vertical position of the video image being projected is adjusted.

H. POS.

: The horizontal position of the video image being projected is adjusted.

BRIGHTNESS

: The brightness of the video image being projected is adjusted.

CONTRAST

: The contrast of the video image being projected is adjusted.

R-GAIN

: The gain in red signal of the video image being projected is adjusted.

G-GAIN

: The gain in green signal of the video image being projected is adjusted.

B-GAIN

: The gain in blue signal of the video image being projected is adjusted.

TEXT MODE

: Adjust easiness for reading text during RESIZE.

 

NORMAL: Normal

 

TEXT 1:

Display the outline of small letters already.

 

TEXT 2:

Makes the outline of large letters sharp.

ALL RESET

: All the items adjusted are reset.

QUICK

 

ALIGN.

OPERATE

 

AV HIDE

PRESET

PAGE BACK

LENS LOCK

PAGE BACK button

N

 

M

 

EN

 

U/

UNLOCK

E

T

 

E

 

R

 

MENU/ENTER button

AV RGB/COMPUTER

U T +

SHIFT ZOOM FOCUS

D W –

LENS

Here, we explain about the operation of the main menu.

For the setting menu, refer to “Making Basic Settings” on page 30.

1 Press the MENU/ENTER button.

• The main menu is displayed on the screen.

2 Press MENU/ENTER toward the 5 or ∞ mark to select an item.

•The selected item (displayed text) is shown in magenta color on the screen.

3 Set (adjust) the item.

■When you have selected DECODER or LANGUAGE,

• Press MENU/ENTER toward the 2 or 3 mark to set.

OPTIONS

MENU AUTO OFF

:

Sets whether to turn off menu display automatically (YES) or not (NO).

LINE DISPLAY

:

Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds after input

 

switching.

RIGHT LEFT REV. : Image is reversed right-to-left.

TOP BOTTOM INV. : Image is inverted top-to-bottom.

CLAMP

: Sets the clamp pulse’s position at the back porch (BP) or on the sink tip (ST). Normally, the clamp

 

pulse is used at BP. If, with some PCs or workstations, the screen becomes unstable such as

 

being too dark or too bright, try to switch to ST.

*To finish the main menu, press the PAGE BACK button.

■When you have selected an item on the submenu,

•Press MENU/ENTER to display the submenu. Then, set (adjust) the item by pressing MENU/ENTER toward the 2/3 or 5/∞ mark.

*To return to the main menu, press PAGE BACK again. To finish the main menu, press PAGE BACK again. (To finish the main menu from the submenu, press PAGE BACK twice.)

No.51666

SOURCE

RESIZE

: When the number of pixels (resolution) sought by the video image input is smaller than that

 

(resolution) of D-ILA device, the video image is then enlarged to a virtually full screen size of D-ILA

 

device and projected. (Resizing indication)

BACK COLOR

: Specifies the background color when there is no image signal. Background color can be selected

 

from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.

COLOR TEMP.

: Adjusts the color temperature of the video image being projected. Make adjustment when the

 

video image becomes reddish or bluish.

 

Color temperature can be set to LOW, MIDDLE, or HIGH.

ASPECT CHANGE : Selects the vertical-to-horizontal ratio of the video image projected. The factory-set ratio is 4 : 3.

 

When projecting high-vision image, a ratio of 16 : 9 can be selected.

SLEEP TIME

: Sets the length of sleep time. A set sleep time after input signal is depleted, the projector goes into

 

a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30 minutes, 60 minutes

 

and 0 minute. (If you select 0 minutes, the sleep time will be cleared.)

LAMP TIME

: Indicates accumulated used hours of the light-source lamp.

:Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.

USER allows you to set a source which is uniquely adjusted by the user.

■Main menu

Submenu items

Input line

 

Source

Channel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C H :

1

 

Y P B P R

 

 

 

 

H D T V ( 1 0 8 0 i )

 

 

 

 

 

 

 

 

 

 

 

 

 

P I X E L C L O C K

P O S I T I O N

P I C T U R E

O P T I O N S

S O U R C E

C H A N N E L

U S E R S O U R C E S E T U P

D I S P L A Y S I Z E

D E C O D E R

N T S C ( 4 8 0 i )

■About main menu display:

Line display: The selected input-mode designation is

displayed. For input-mode designation, “Y/C”, “VIDEO”, “Y, PB/B-Y, PR/R-Y”, “COMPUTER 1” and “COMPUTER 2” are available.

Source display: The type of signal being input is displayed. With this projector, unique designations are previously given to specific horizontal and vertical frequencies. This allows the source selected under SOURCE (submenu item) to be indicated. The source setting can be selected from AUTO mode, dedicated (forced) modes and USER mode. When AUTO is selected, the horizontal and vertical frequencies of a signal being input are detected and the matched designation is displayed in ( ).

Display example: “AUTO (NTSC(480i))”

CHANNEL

USER SOURCE SET UP

DISPLAY SIZE

DECODER LANGUAGE

:Sets a line and multiple sources for each channel.

:Sets up an area for the source being input, and registers the user name.

:Adjusts H PIXEL, V PIXEL, H CENTER and V CENTER of video image.

:Does not work with computer-related inputs. (The color system is indicated in gray.)

:Text on the screen can be changed to a language other than English. Languages that can be displayed are the

following six : (Japanese), ENGLISH, DEUTSCH (German), ESPAÑOL (Spanish), ITALIANO (Italian), and FRANÇAIS (French). However, some text such as “QUICK ALIGNMENT”, etc. are shown only in English.

L A N G U A G E

E N G L I S H

Decoder (color system) Language

Therefore, be careful as the source display does not always correspond to the indication or type of the input signal.

For the unique designations for the specific horizontal and vertical frequencies, see page 19.

Channel display: The channel selected by the user is displayed. The line, sources and switcher No. selected by the user have been registered to the channel. Once registered, the line, sources and switcher No. of the projector will change to the ones the user has registered only by switching between channels. The settings should be made on the “Channel setup/selection menu”. For details, see page 47.

Submenu item display:

See pages 36 to 58.

Decoder (Color system) display: See page 34.

Language display:

See page 35.

DLA- DLA-

32

33

M4000LU M4000LE

Page 16 Page 18
Image 17
Page 16 Page 18
Contents For customer Use OperatingLamp directly by opening the cabinet while the illumination About burning-in of the D-ILA deviceContents Accessories Controls and Features Controls and FeaturesFront Side / Top Surface / Right Side Left-hand side / Back SideControl Panel Remote Control Unit Connector PanelInstall the batteries Installing BatteriesMenu / Enter Menu Operation Button Open the back coverPrecautions for Installation Installing the ProjectorInstalling the Projector Relationship relative to Glass SurfaceChange of projection screen according Lens Shift FunctionTo aspect ratio ScreenSignals that Can Be Input to the Projector Connecting to Various DevicesAdjustable range of the lens Projection Distances and Screen SizesRGB output devices Example of a basic systemDesktop type Connecting the Power Cord Supplied Connecting to Devices which Control the ProjectorPower cord into a wall outlet, Insert the plug of the suppliedTurning on the Power When Turning On the Devices Connected to the ProjectorTurning off the Power Basic OperationsAdjust focus Adjust the screen sizeFor Operating Other Functions Basic OperationsTo use the remote control’s Preset button To display the Setting menuProjector’s button To display Channel on the screenMaking Basic Settings Operating the Setting Menu Operating the Main MenuPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Basic Operation of the Main Menu Configuration of the Main Menu Computer-related inputChanging the Language Display Changing the Color SystemPress MENU/ENTER toward the 5 or ∞ mark to select Decoder Press MENU/ENTER toward the 2 or 3 mark to setAdjusting the Screen Position Adjusting the Pixel ClockAdjustment item Button Adjustment content To return to the main menu, pressSubmenu items Adjusting Picture QualityFollowing optional functions can be set adjusted Setting and Adjusting Other Functions OptionsAbout the lamp use time Picture menuOptions menu Adjustment item ButtonDisplay, the video image resolution becomes coarse Press the MENU/ENTER button Submenu Changing Setting the SourcePress MENU/ENTER to set fix Press MENU/ENTER to set Setting Up ChannelsPress the MENU/ENTER button to set Setting Up Channels Source setup Setting Up Channels Line setupChannel setup selection menu When Line is selectedPress the page Back button to set Setting Up Channels SWNo. setupWhen a switcher number SWNo is selected Changing Channels CH Change Setting Up or Changing User Sources Mark to select a submenu item Remote control unit Press the MENU/ENTER button to setSetting Up or Changing the Display Size Remove the filter cover screws Cleaning and Replacing the FilterRemove the filters To return to the main menu, press page BACK. To finishClean the filters TroubleshootingReinstall the filters About Light-Source Lamp ReplacementTroubleshooting When the emergency indicator starts blinkingSpecifications SpecificationsEXT. in AV in input RGB in RGB inputDTV-format signals Victor Company of JAPAN, Limited DLA-M4000LE InstructionsImportant Information Improper adjustment of controls may result in damageContents Controls and Features Temp indicator On When in stand-by mode Blinking When in cool-down modeOn When the projector is in operation projecting Input of external sync signals is automatically detected 51666 305 mm 600 mm 11.392 Type
Related manuals
Manual 68 pages 40.21 Kb
Top Page Image Contents