Luce PT-L6510E, PT-L6600E manual LMPORTANT the Moulded Plug U.K. only

Page 3

lMPORTANT: THE MOULDED PLUG (U.K. only)

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moutded three pin mains plug for your safety and convenience. A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362. Cheque for the ASTA mark or the BSl mark on the body of the fuse.

lf the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. lf you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from an Authorized Service Centre.

If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse should be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

WARNING: –THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: –The wires in this mains lead are coloured in accordance

with the following code: – Green-and-Yellow: Earth

Blue:Neutral

Brown:Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol or coloured GREEN or

GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

FUSE

How to replace the fuse. Open the fuse compartment with a screwdriver and replace the fuse.

ENGLISH

3

Image 3

Contents LCD Projector Commercial Use PT-L6600EDear Panasonic Customer Important Safety NoticeLMPORTANT the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being used AccessoriesPower cord plug from the wall outlet Precautions on handlingSystem Example of System upLocation and function of each part Remote ControlProjector Top · Front and Side Projector Top · Rear and Side Rear control panel Location and function of each partInterface panel Using the Remote control unit Loading batteriesEffective control range Laser Specifications Using laser pointerSetting projector IDs for remote control Press the ID SET button on remote controlUsing the remote control as a PC mouse Using the Remote control unitUsing the remote control in wired mode Projection Distances Setting-upInstallation Geometry Projection SchemesPin assignments on the RGB2 input port are as follows Setup precautionsExample of connecting with AV products Setting-upColour monitor with RGB video ports Example of connecting with PCsSystem switcher Example of connecting with system switcherStarting to use Powering Up the ProjectorMaking Initial Adjustment Setting input port Powering Off the ProjectorRetracting the Leveling Feet Adjusting the Vertical Position PictureStarting to use Leveling the ProjectorStill image Using the Freeze functionUsing the Shutter function Advice on the installation of exhaust guidesUsing the Digital Zoom D.ZOOM +/- function Menu screens On-screen menusBasic Menu Operations Menu Items SettingReset the Factory Default On-screen menusUsing the Index Window function PT-L6510E only Adjusting the picture Standard Signal ModeTV-SYSTEM BAL White balance R/G/BAdjusting the position Focus What Is S1 Video?Aspect ZoomBack Colour Option 1 settingsRGB Format Lens ShiftLamp Select Option 2 settingsLamp Power Setting Function 1 FuncOption 2 settings Setting Unit IDRegistering/Deleting Displaying User Mode Using the Serial Connecting to a computer Using the SerialControl command Cable specificationsUsing the remote terminal Pin assignment and controlExample of a control panel layout Indication of lamp monitor Indicator Display Condition Check MeasuresCleaning method Cleaning and replacing the air filterDisplay after 1800 hours Lamp replacement periodReplacing the lamp unit Model No Lamp unit model NoLamp unit replacement steps Replacing the lamp unit Press the Power button to turn off the powerNo image Symptoms ChequesPower does Not turn onSpecifications Remote RGB2 input Audio input For RGB 1/2Video RGB outputAppendix Compatible RGB SignalsDimensions Trademark acknowledgmentsTrademark M1002-0