Luce PT-L6600E Option 2 settings, Setting Unit ID, Registering/Deleting Displaying User Mode

Page 36

OPTION 2 settings

SETTING UNIT ID

UNIT ID is used to set projector IDs when the user wishes to control two or more projectors either simultaneously or separately.

SET ID

ALL

 

 

 

 

 

 

1

2

3

"ALL": The projectors can be simultaneously controlled from any remote control regardless of their ID settings.

"1": The projector can be controlled from the remote control with its projector ID set to “1”.

"2": The projector can be controlled from the remote control with its projector ID set to “2”.

"3": The projector can be controlled from the remote control with its projector ID set to “3”.

Note

Unit ID is set to “ALL” by default. Hence ID number need not be set when only one projector is used.

If the projectors are given ID numbers, their remote controls must be assigned the same ID numbers, respectively.

If the unit IDs of two or more projectors are set to “ALL”, the user will not be able to control them separately.

The projector can be turned ON/OFF from the remote control only if the projector ID is set in the remote control. For the details of projector ID setting, see page 15.

Registering/Deleting/

Displaying User Mode

(For RGB/YPBPR signals only)

Once adjustment settings are registered with User Mode, they are automatically loaded each time the projector is powered up. It is not necessary to readjust settings at every power on.

Registering User Mode

(e.g. Registering positioning data with “USER1”)

1.Apply an input signal you want to register, and then adjust the picture position, size, and others.

2.Choose “USER MODE” on “OPTION2” and press the “ENTER” button.

USER MODE

ENTRYUSER1

SELECT

ADJ

 

 

 

ESC

 

 

3.Choose “USER1” using the or buttons and press the “ENTER” button.

Note

The user address has “USER1” to “USER3”.

4.After recognizing the flashing of the USER1 address display, press the “ENTER” button again.

5.The above adjusted settings has been registered with “USER1”. Similarly you can also register settings with “USER2” or “USER3”.

Deleting User Mode

(e.g. Deleting the data of “USER1”)

1.Choose “USER MODE” on “OPTION2” and press the “ENTER” button.

2.Choose “DELETE” using the or buttons.

3.Choose the address (USER1) you want to delete data from using the or buttons and press the “ENTER” button.

USER MODE

ENTRY

 

USER1

DELETE

 

USER1

SELECT

ADJ

 

 

 

ESC

 

 

 

 

4.After recorgnizing the flashing of the address display, press the “ENTER” button again to delete the data of the address.

Displaying User Mode

The User Mode can be displayed by following the steps described in “SIGNAL MODE” on page 31.

36

Image 36
Contents PT-L6600E LCD Projector Commercial UseImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully LMPORTANT the Moulded Plug U.K. onlyContents Precautions with regard to safety Precautions with regard to safety Accessories Do not look into the lens while the projector is being usedPrecautions on handling Power cord plug from the wall outletExample of System up SystemRemote Control Location and function of each partProjector Top · Front and Side Location and function of each part Projector Top · Rear and Side Rear control panelInterface panel Using the Remote control unit Loading batteriesEffective control range Using laser pointer Setting projector IDs for remote controlPress the ID SET button on remote control Laser SpecificationsUsing the Remote control unit Using the remote control as a PC mouseUsing the remote control in wired mode Setting-up Installation GeometryProjection Schemes Projection DistancesSetup precautions Pin assignments on the RGB2 input port are as followsSetting-up Example of connecting with AV productsExample of connecting with PCs Colour monitor with RGB video portsExample of connecting with system switcher System switcherPowering Up the Projector Making Initial Adjustment Setting input portPowering Off the Projector Starting to useAdjusting the Vertical Position Picture Starting to useLeveling the Projector Retracting the Leveling FeetUsing the Freeze function Using the Shutter functionAdvice on the installation of exhaust guides Still imageUsing the Digital Zoom D.ZOOM +/- function On-screen menus Menu screensMenu Items Setting Reset the Factory DefaultOn-screen menus Basic Menu OperationsUsing the Index Window function PT-L6510E only Adjusting the picture Signal Mode TV-SYSTEMBAL White balance R/G/B StandardAdjusting the position What Is S1 Video? AspectZoom FocusOption 1 settings RGB FormatLens Shift Back ColourOption 2 settings Lamp PowerSetting Function 1 Func Lamp SelectOption 2 settings Setting Unit IDRegistering/Deleting Displaying User Mode Using the Serial Using the Serial Control commandCable specifications Connecting to a computerUsing the remote terminal Pin assignment and controlExample of a control panel layout Indicator Display Condition Check Measures Indication of lamp monitorCleaning and replacing the air filter Cleaning methodLamp replacement period Replacing the lamp unitModel No Lamp unit model No Display after 1800 hoursLamp unit replacement steps Press the Power button to turn off the power Replacing the lamp unitSymptoms Cheques Power doesNot turn on No imageSpecifications RGB2 input Audio input For RGB 1/2 VideoRGB output RemoteCompatible RGB Signals AppendixDimensions Trademark acknowledgmentsTrademark M1002-0