Luce PT-L6510E Symptoms Cheques, Power does, Not turn on, No image, Image is blurred, No sound

Page 45

Before asking for service ---Before asking for service, cheque the following points.

Symptoms

 

Cheques

 

 

 

• Is the power cord plug correctly plugged in?

 

• Is the MAIN POWER turned on?

Power does

• Is electricity running to the power outlet?

• Is the temperature monitor (TEMP) indicator on the front of the unit flashing or

not turn on

turned on? (See page 40)

 

• Is the lamp monitor (LAMP) indicator on the front of the unit flashing or turned on?

 

(See page 40)

 

 

• Is the lamp unit door installed correctly?

 

• A wrong ID is set. (See pages 15 and 36)

 

 

 

• Is the lens cap still on the lens?

 

• Is the image input correctly connected?

No image

• Is the input mode set correctly? (See page 23)

• Is the black level adjustment set at the minimum level? (See page 30)

 

 

• Is the equipment connected to the projector operating correctly?

 

• Is the shutter function turned on? (See page 25)

 

 

 

• Is the lens focused properly? (See page 23)

Image is blurred

• Is the projection distance correct? (See page 18)

• Is the lens dirty?

 

 

 

 

• Is the projector positioned directly in front of the screen? (See page 18)

 

 

Light colour/

• Is the colour density and colour tone setting correct? (See page 30)

bad colour tone

• Is the equipment connected to the projector correctly adjusted?

 

 

 

• Is the sound input correctly connected?

No sound

• Is the volume set to the minimum level? (See page 23 and 27)

• Is the shutter or mute turned on? (See page 25 and 35)

 

 

• Is the cable connected to the AUDIO OUT terminal?

 

 

 

• Are the batteries exhausted?

 

• Are the battery polarities set correctly? (See page 14)

 

• Are their any obstacles between the remote control and the remote control sensor?

Remote control

(See page 14)

 

does not operate

• Are you trying to operate the remote control beyond its operable range? (See page 14)

 

• Are you controlling from external equipment using the REMOTE terminal? (See

 

page 39)

 

 

• Is their any external light interfering with remote control operation?

 

• A wrong ID is set. (See pages 15 and 36)

 

 

 

• Is the input mode properly set? (See page 23)

Abnormal image

• Is the correct signal system (TV system) selected? (See page 31)

• Are their any malfunctions on the source side, such as bad video tapes?

 

 

• Are you inputting a signal that is not compatible with this projector? (See page 48)

 

 

Does not display

• Is the cable too long?

• Is the video output signal setting of the notebook computer correctly set?

images from PCs

Setting :

key (Read the operating instructions of the your PC.)

 

 

 

 

ENGLISH

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents LCD Projector Commercial Use PT-L6600EDear Panasonic Customer Important Safety NoticeLMPORTANT the Moulded Plug U.K. only For Your SAFETY, Please Read the Following Text CarefullyContents Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being used AccessoriesPower cord plug from the wall outlet Precautions on handlingSystem Example of System upLocation and function of each part Remote ControlProjector Top · Front and Side Projector Top · Rear and Side Rear control panel Location and function of each partInterface panel Using the Remote control unit Loading batteriesEffective control range Setting projector IDs for remote control Using laser pointerPress the ID SET button on remote control Laser SpecificationsUsing the remote control as a PC mouse Using the Remote control unitUsing the remote control in wired mode Installation Geometry Setting-upProjection Schemes Projection DistancesPin assignments on the RGB2 input port are as follows Setup precautionsExample of connecting with AV products Setting-upColour monitor with RGB video ports Example of connecting with PCsSystem switcher Example of connecting with system switcherMaking Initial Adjustment Setting input port Powering Up the ProjectorPowering Off the Projector Starting to useStarting to use Adjusting the Vertical Position PictureLeveling the Projector Retracting the Leveling FeetUsing the Shutter function Using the Freeze functionAdvice on the installation of exhaust guides Still imageUsing the Digital Zoom D.ZOOM +/- function Menu screens On-screen menusReset the Factory Default Menu Items SettingOn-screen menus Basic Menu OperationsUsing the Index Window function PT-L6510E only Adjusting the picture TV-SYSTEM Signal ModeBAL White balance R/G/B StandardAdjusting the position Aspect What Is S1 Video?Zoom FocusRGB Format Option 1 settingsLens Shift Back ColourLamp Power Option 2 settingsSetting Function 1 Func Lamp SelectOption 2 settings Setting Unit IDRegistering/Deleting Displaying User Mode Using the Serial Control command Using the SerialCable specifications Connecting to a computerUsing the remote terminal Pin assignment and controlExample of a control panel layout Indication of lamp monitor Indicator Display Condition Check MeasuresCleaning method Cleaning and replacing the air filterReplacing the lamp unit Lamp replacement periodModel No Lamp unit model No Display after 1800 hoursLamp unit replacement steps Replacing the lamp unit Press the Power button to turn off the powerPower does Symptoms ChequesNot turn on No imageSpecifications Video RGB2 input Audio input For RGB 1/2RGB output RemoteAppendix Compatible RGB SignalsDimensions Trademark acknowledgmentsTrademark M1002-0
Top Page Image Contents