OPTION 2 settings
1.Obtain the MENU window and select (highlight) the desired adjustment item
with the
or 
buttons (on the projector or remote control).
2. Adjust the parameter value for the selected item with the 
or 
buttons.
OPTION 2
LAMP POWER |
|
| HIGH | ||||
LAMP SELECT |
|
| DUAL |
| |||
LAMP RUNTIME |
| 1 | 7 | H | |||
FUNCTION 1 |
|
| MUTE |
| |||
SET ID |
|
| ALL |
| |||
USER MODE |
|
|
|
|
|
|
|
SELECT | ADJ |
|
|
|
| ESC | |
|
|
| |||||
|
|
| |||||
LAMP POWER
“LAMP POWER” is used to change the luminance of the projection lamp depending on user's needs or the
viewing conditions. | LAMP POWER | HIGH | ||
|
|
|
|
|
|
|
|
|
|
STANDARD
HIGH: Choose if a higher picture brightness is required.
STANDARD: Choose for normal picture brightness.
Note
•If it is not necessary for picture brightness to be very high (in a small meeting room, etc.), it is advisable that you set BRIGHTNESS to “STANDARD”. This will save power consumption and extend lamp life.
LAMP SELECT
“LAMP SELECT” is used to choose from Single Lamp and Dual Lamp modes depending on user's needs or viewing conditions. In Single Lamp mode, the projector may automatically select either lamp from the 2 lamps, or the particular lamp can be specified.
LAMP SELECT |
| DUAL |
| * Press and hold the “ENTER” | |
|
| ||||
|
|
|
|
| button for approximately 3 |
|
|
|
|
| |
| SINGLE | ||||
|
| seconds. (lamp with longer | |||
|
|
|
|
| |
|
|
|
| operating hours is turned | |
| SINGLE 1 | ||||
|
|
|
|
| off) |
|
|
|
| ||
| SINGLE 2 |
|
| ||
DUAL: Two lamps are used simultaneously.
SINGLE: One of either lamps is used (lamp with shorter operating hours is automatically selected). SINGLE 1: Lamp Unit 1 is always used.
SINGLE 2: Lamp Unit 2 is always used.
Caution
•Lamp can be selected without turning off the projector.
•If lamp mode is switched from “SINGLE”, “SINGLE 1”, or “SINGLE 2” into “DUAL”, be sure to temporarily turn the projector OFF, then turn it ON again. The “DUAL” mode will become valid only after the projector is turned back ON.
Note
•When the currently active lamp exceeds 2000 hours of cumulative operating time, if in “SINGLE 1” or “SINGLE 2” mode, the other lamp takes over, provided that the cumulative operating time of that lamp does not exceed 2000 hours.If the cumulative operating time of the other lamp also exceeds 2000 hours when in “DUAL”, “SINGLE”, “SINGLE 1”, or “SINGLE 2” mode, the projector will enter Standby mode after 10 minutes.
•If only one lamp is installed in the projector, set lamp mode to either “SINGLE 1” or “SINGLE 2”. “SINGLE 1” or “SINGLE 2” is selected. If the corresponding lamp is not installed, the other lamp will turn on. The same holds for “SINGLE 2” mode. If “SINGLE” mode is selected, it may take approx. 90 seconds before the lamp turns ON.
LAMP RUNTIME
“LAMP RUNTIME” is used to cheque the cumulative operating hours of the two projection lamps.
LAMP RUNTIME | 1 |
| 11 H |
|
|
|
|
|
|
|
|
| 2 |
| 11 H |
“1”: Lamp 1 operating hours is displayed.
“2”: Lamp 2 operating hours is displayed.
Note
•If the cumulative operating hours exceeds 1800 hours, the hour indicator flashes in red.
SETTING FUNCTION 1 [FUNC 1]
FUNCTION 1 is used to specify the function of the remote control / “FUNC1” button. (“FUNC1” button functions differ between the
•
FUNCTION 1 | INDEX | ||
|
|
|
|
|
|
|
|
MUTE
STANDARD
•
FUNCTION 1 | MUTE | ||
|
|
|
|
|
|
|
|
STANDARD
INDEX: Pressing the “FUNC1” button displays both still and motion images on a split screen (same as the “INDEX WINDOW” option in the MAIN MENU).
MUTE: Pressing the “FUNC1” button mutes the sound output.
STANDARD: Pressing the “FUNC1” button resets all the parameter values now in the menu t o t h e f a c t o r y d e f a u l t , w i t h a “STANDARD” indicator shown in the upper right corner of the menu.
ENGLISH
35