Luce PT-L6600E Replacing the lamp unit, Lamp replacement period, Model No Lamp unit model No

Page 42

Replacing the lamp unit

Caution!

Replacement of the lamp unit should only be carried out by a qualified technician.

Notes when replacing the lamp unit:

Caution!

Replace the lamp unit only after it has completely cooled off.

•The internal pressure of the light source is high, therefore if it is struck by hard objects or dropped, it may cause damage. Be careful when handling.

•Handle the old lamp unit with care as it is easily broken.

•A Philips screwdriver is necessary when replacing the lamp unit. Be careful not to slip when using the screwdriver.

Caution

• The lamp unit is sold separately. Please consult the service/parts centre at your dealer.

	Model No.	Lamp unit model No.
	PT-L6510E	ET-LAL6510 (1 lamp) • ET-LAL6510W (2 lamps)
	PT-L6600E	ET-LAL6510 (1 lamp) • ET-LAL6510W (2 lamps)
	PT-L6600E

•Lamps other than those indicated above must not be used with this projector. Be sure to use the specified lamp.

Lamp replacement period

The light source lamp of this projector has a life cycle of 2000 hours (Lamp power---hi, Lamp selection---dual setting). However, this duration may be reduced depending on the usage of the projector-the frequency in which the light is turned on and of its intervals affect the life of the lamp. Therefore it is recommended that a spare lamp be made available before 2000 hours have elapsed. If the lamp unit is not replaced after 1800 hours, the power will automatically shut off after 2000 hours and enter standby mode. If the power is turned on after 2000 hours, it will turn off automatically after approximately 10 minutes and enter standby mode.

Note

• 2,000 hours is a guideline for replacement, not a guarantee time.

• Display after 1800 hours

The lamp monitor indicators (LAMP 1 or LAMP2) will light after the lamp unit runtime has elapsed 1800 hours even during standby mode.

An on - screen message indicating lamp replacement is necessary will be displayed on the screen 30 seconds.

(This on-screen message will disappear after 30 seconds or the projector operation buttons remote control buttons are operated.)

This on-screen message does not disappear, unless a “MENU” buttons or sound adjustment “(VOLUME +/-)” buttons will be pushed, if it reaches in 2000 hours.

	S-VIDEO
REPLACE LAMP	AUTO

42

Image 42

Contents PT-L6600E LCD Projector Commercial UseImportant Safety Notice Dear Panasonic CustomerFor Your SAFETY, Please Read the Following Text Carefully LMPORTANT the Moulded Plug U.K. onlyContents Precautions with regard to safety Precautions with regard to safety Accessories Do not look into the lens while the projector is being usedPrecautions on handling Power cord plug from the wall outletExample of System up SystemRemote Control Location and function of each partProjector Top · Front and Side Location and function of each part Projector Top · Rear and Side Rear control panelInterface panel Using the Remote control unit Loading batteriesEffective control range Press the ID SET button on remote control Using laser pointerSetting projector IDs for remote control Laser SpecificationsUsing the Remote control unit Using the remote control as a PC mouseUsing the remote control in wired mode Projection Schemes Setting-upInstallation Geometry Projection DistancesSetup precautions Pin assignments on the RGB2 input port are as followsSetting-up Example of connecting with AV productsExample of connecting with PCs Colour monitor with RGB video portsExample of connecting with system switcher System switcherPowering Off the Projector Powering Up the ProjectorMaking Initial Adjustment Setting input port Starting to useLeveling the Projector Adjusting the Vertical Position PictureStarting to use Retracting the Leveling FeetAdvice on the installation of exhaust guides Using the Freeze functionUsing the Shutter function Still imageUsing the Digital Zoom D.ZOOM +/- function On-screen menus Menu screensOn-screen menus Menu Items SettingReset the Factory Default Basic Menu OperationsUsing the Index Window function PT-L6510E only Adjusting the picture BAL White balance R/G/B Signal ModeTV-SYSTEM StandardAdjusting the position Zoom What Is S1 Video?Aspect FocusLens Shift Option 1 settingsRGB Format Back ColourSetting Function 1 Func Option 2 settingsLamp Power Lamp SelectOption 2 settings Setting Unit IDRegistering/Deleting Displaying User Mode Using the Serial Cable specifications Using the SerialControl command Connecting to a computerUsing the remote terminal Pin assignment and controlExample of a control panel layout Indicator Display Condition Check Measures Indication of lamp monitorCleaning and replacing the air filter Cleaning methodModel No Lamp unit model No Lamp replacement periodReplacing the lamp unit Display after 1800 hoursLamp unit replacement steps Press the Power button to turn off the power Replacing the lamp unitNot turn on Symptoms ChequesPower does No imageSpecifications RGB output RGB2 input Audio input For RGB 1/2Video RemoteCompatible RGB Signals AppendixDimensions Trademark acknowledgmentsTrademark M1002-0