TANDBERG 5000 user manual Getting started, System start-up, On-screen help

Page 23

VISION 5000 Videoconferencing System

Getting started

System start-up

Your Vision 5000 should be in standby mode, if so pressing any key will wake up the system.

If the Vision 5000 does not respond: turn on the system by using the On/Off switch located at the rear of the Codec, see figure below. After a few seconds you should see a start-up message on the monitor.

If this does not help, check if your monitor is switched on. To switch your monitor on you normally push the power button in front of the monitor (depending on monitor type).

On/Off

On-screen help

Press the HELP key to get help.

The help system has two formats:

1.A separate Help Menu.

2.Context sensitive help, i.e. HELP relative to wherever you are in the menu system.

Image 23

Contents N D B E R G Vision 5000 Videoconferencing System Lysaker, Norway, Tel +47 67 125 125, Fax +47 67 125 Environmental IssuesVision 5000 Videoconferencing System Operator Safety Summary Contents Appendices Index Vision 5000 Videoconferencing System Advanced useEthernet Functionality Peripheral EquipmentIntroduction How to use this guideMain menu Menu structureVision 5000 on-screen menu structure is shown below Right keys to move through the menu structureAt a glance the Vision 5000 system Vision 5000 videoconferencing systemCodec Vision 5000 Videoconferencing System CameraMonitors Vision 5000 Videoconferencing System Cart Remote controlTandberg AudioScience module optional Vision 5000 Videoconferencing System Table microphoneTandberg Natural Audio module optional on some systems This product complies with directives 89/366/EEC 93/261/EEC InstallationPrecautions Vision 5000 Videoconferencing System InstallationUnpacking Installation Vision 5000 Videoconferencing SystemCamera Table Microphone Remote Control Batteries Connecting to the Switched 56 network Connecting cablesIsdn cables using BRI interface Isdn cable using the PRI/T1 interfacePress OK to exit menu Power on monitorExample 29 monitor not USA Example 33 monitor not USAPress p+s/tp- to select Special FUNCTIONS, then press OK Power on codecTo highlight Switch on with, select AV with + keys Example monitor USAExternal Network configuration ConfigurationISDN-BRI configuration ISDN-PRI/T1 configurationBackground Environmental considerationsIris control and lighting Do not place the camera facing a doorway Loudspeaker volumeBrightness control Seating Area Table LightingVision Vision 5000 Videoconferencing System Getting started Getting startedSystem start-up On-screen helpTo confirm the selection press OK BasicsGetting started Vision 5000 Videoconferencing System Video call Making and ending callsMaking a call Prefix Call Type Restricted callTelephone call SoftMux only Special call prefixesTo answer a call, press Last number redial/using the call directoryIs switched off. See ‘Utilities’ Correcting keying mistakesGeneral use Vision 5000 Videoconferencing System Adjusting volumeGeneral use View outgoing videoControlling the Main Camera Microphone on/offMoving the picture-in-picture PIP To manually focus the Main Camera, use the Focus keys Camera TrackingHighlighter bar to a source and press OK Enable/Disable Camera TrackingSelecting video sources Selecting audio sourcesStoring presets PresetsSelecting presets Requesting a still image Sending/receiving graphicsSending a still image Source and 0 to view the still image Receiving a still imageFar end camera control Fecc Overview Advanced useGeneral Advanced use Vision 5000 Videoconferencing SystemAll submenus are explained below Main menuMenu structure Video Call qualityAudio Motion Video ModeAudio QualityStatus Format ResolutionLow resolution video 176 x 144 pixels ChannelsAlphabetic Sort Edit directoryBoth numbers should be specified 2x64 or 2x56 calls Add New EntryKey to delete the last character Store Last Number Far end camera control UtilitiesAutoanswer Do not disturbSystem Name Presentation SettingsThis menu allows setup of still-image/graphics transfer MCU status lineTest subsystem Power up and system infoView current settings You can test the different subsystems of the VisionCall status BRI Status BRI Status PRI CommentsCall status PRI Cause codes Most common cause codes for Isdn areRequest floor MCU servicesRelease chair Terminal IDChair control Take chairAllows the chairman to terminate the conference altogether Allows the chairman to release the floorAudio Inputs Audio setupMic1 +3.0dB Mix ModeLevel Settings Inputs If an output is ‘Off’, no audio will be sent to that output Level Settings OutputsEcho Control Noise ReductionTips for improving the echo canceller performance Alert Speaker Alert Tones & VolumeRestore Audio Defaults Enter a video source name Camera Track ModeVideo input Backlight Camera adjustmentsKeys on the remote control FocusWhitebalance Vision 5000 Videoconferencing System Advanced use BrightnessVideo output ISDN-BRI ISDN-PRI/T1 External Terminal settingsNetwork configuration Etsi Euro Isdn Isdn switch typeNtsc version is shown below Number2 Number Line SetupSubaddress Advanced Isdn settingsDownspeed Default Call TypeMSN Multi Subscriber Number Parallel dialCable Length 1&2 NumberMax Channels Channel Hunting Type Manufacturer PRI Switch Type settingPRI Switch Type AT&T Isdn National IsdnCall control RS366 Dialling Leased Line Data Triggered ManualRS449/V35 Compatible #006 6B call Bonding #002 #008 8B call Bonding #003None Dataport configurationDataport 9600Dataport 1 supports 4 different modes Control Modem 120 Data modeControl mode Modem modeRestore defaults IP-subnet mask TCP/IP SettingsIP-assignment IP-addressEthernet Vision 5000 Videoconferencing System What is neededEthernet Functionality WWW-interfaceVision 5000 Videoconferencing System Ethernet How is it done Peripherals Vision 5000 Videoconferencing System Peripheral EquipmentVideo Outputs InterfacesVision 5000 Videoconferencing System Peripherals Video InputsDual Monitor optional Please contact your dealer for further information Natural Audio module optionalAudioScience module optional Tracker optional Multiple controllable cameras optionalDocument camera VCR Recording Video Cassette Recorder VCRVCR Playback Extra cameras Telephone Add-OnVGA PAL/NTSC converter PC applicationsVGA to PAL converter Other PC applicationsAdditional microphones Appendix Vision 5000 Videoconferencing System AppendicesVision 5000 Videoconferencing System Appendix Using Telesync TS-256 SW56/ISDN adapterVision Configuration of VisionINC DSU Making a call Appendix 3 Connecting Vision 5000 to PRI/T1Using CSU adapter Configuration ofAdtran T1 ESF CsuaceAppendix 4 LED indication PowerIndex Vision 5000 Videoconferencing System SymbolsIndex Imux Vision 5000 Videoconferencing System IndexIndex Vision 5000 Videoconferencing System