TANDBERG 5000 user manual Camera Tracking, To manually focus the Main Camera, use the Focus keys

Page 30

General use

VISION 5000 Videoconferencing System

Focusing camera

To manually focus the Main Camera, use the Focus keys:

FOCUS

The Main Camera is set for autofocus by default. An on screen indicator will appear whenever autofocus is On.

If the Main Camera is moved (pan/tilt/zoom), autofocus will be switched On automatically for 5 seconds.

Camera Tracking

Before using camera tracking, presets P7 (Mic1), P8 (Mic2) and/or P9 (Mic3) must be stored using Video Input #1 as the video source.

Example:

The camera position stored at P7 must be related to Mic1, therefore all participants which are located closest to Mic1 should be included in the P7 camera position etc.

When camera tracking is activated and a person close to Mic1 speaks, P7 will be automatically selected.

If a person close to Mic1 has a conversation with a person close to Mic2, the camera will adjust to a camera position which includes both persons.

Start camera tracking by selecting # in the ‘Video Source’ menu (see the ‘Selecting video sources’ section for starting/stopping camera tracking).

When activating another video source (e.g. document camera), camera tracking will temporarily be disabled until you select MainCam or a MainCam preset.

Pressing MIC OFF will temporarily disable camera tracking.

A Voice Detector makes the system more tolerent against noise and the camera will normally not be moved by noise like paper shuffling etc.

The camera tracking speeds may be altered in the ‘Video Input’ menu. See ‘Advanced use’ for further details.

30

Image 30
Contents N D B E R G Vision 5000 Videoconferencing System Environmental Issues Lysaker, Norway, Tel +47 67 125 125, Fax +47 67 125Vision 5000 Videoconferencing System Operator Safety Summary Contents Peripheral Equipment Vision 5000 Videoconferencing System Advanced useEthernet Functionality Appendices IndexHow to use this guide IntroductionRight keys to move through the menu structure Menu structureVision 5000 on-screen menu structure is shown below Main menuVision 5000 videoconferencing system At a glance the Vision 5000 systemVision 5000 Videoconferencing System Camera MonitorsCodec Remote control Vision 5000 Videoconferencing System CartVision 5000 Videoconferencing System Table microphone Tandberg Natural Audio module optional on some systemsTandberg AudioScience module optional Vision 5000 Videoconferencing System Installation InstallationPrecautions This product complies with directives 89/366/EEC 93/261/EECInstallation Vision 5000 Videoconferencing System Camera Table Microphone Remote Control BatteriesUnpacking Isdn cable using the PRI/T1 interface Connecting cablesIsdn cables using BRI interface Connecting to the Switched 56 networkExample 33 monitor not USA Power on monitorExample 29 monitor not USA Press OK to exit menuExample monitor USA Power on codecTo highlight Switch on with, select AV with + keys Press p+s/tp- to select Special FUNCTIONS, then press OKISDN-PRI/T1 configuration ConfigurationISDN-BRI configuration External Network configurationEnvironmental considerations Iris control and lightingBackground Loudspeaker volume Brightness controlDo not place the camera facing a doorway Lighting Seating Area TableVision On-screen help Getting startedSystem start-up Vision 5000 Videoconferencing System Getting startedBasics Getting started Vision 5000 Videoconferencing SystemTo confirm the selection press OK Making and ending calls Making a callVideo call Special call prefixes Restricted callTelephone call SoftMux only Prefix Call TypeCorrecting keying mistakes Last number redial/using the call directoryIs switched off. See ‘Utilities’ To answer a call, pressView outgoing video Adjusting volumeGeneral use General use Vision 5000 Videoconferencing SystemMicrophone on/off Moving the picture-in-picture PIPControlling the Main Camera Camera Tracking To manually focus the Main Camera, use the Focus keysSelecting audio sources Enable/Disable Camera TrackingSelecting video sources Highlighter bar to a source and press OKPresets Selecting presetsStoring presets Sending/receiving graphics Sending a still imageRequesting a still image Receiving a still image Source and 0 to view the still imageFar end camera control Fecc Advanced use Vision 5000 Videoconferencing System Advanced useGeneral OverviewMain menu Menu structureAll submenus are explained below Call quality AudioVideo Quality Video ModeAudio MotionChannels ResolutionLow resolution video 176 x 144 pixels Status FormatEdit directory Alphabetic SortAdd New Entry Key to delete the last characterBoth numbers should be specified 2x64 or 2x56 calls Store Last Number Do not disturb UtilitiesAutoanswer Far end camera controlMCU status line Presentation SettingsThis menu allows setup of still-image/graphics transfer System NameYou can test the different subsystems of the Vision Power up and system infoView current settings Test subsystemStatus BRI Status PRI Comments Call status BRICall status PRI Most common cause codes for Isdn are Cause codesMCU services Request floorTake chair Terminal IDChair control Release chairAllows the chairman to release the floor Allows the chairman to terminate the conference altogetherAudio setup Audio InputsMix Mode Level Settings InputsMic1 +3.0dB Level Settings Outputs If an output is ‘Off’, no audio will be sent to that outputNoise Reduction Echo ControlTips for improving the echo canceller performance Alert Tones & Volume Restore Audio DefaultsAlert Speaker Camera Track Mode Video inputEnter a video source name Focus Camera adjustmentsKeys on the remote control BacklightVision 5000 Videoconferencing System Advanced use Brightness WhitebalanceVideo output Terminal settings Network configurationISDN-BRI ISDN-PRI/T1 External Isdn switch type Ntsc version is shown belowEtsi Euro Isdn Number Line Setup Number2Advanced Isdn settings SubaddressParallel dial Default Call TypeMSN Multi Subscriber Number DownspeedNumber Max ChannelsCable Length 1&2 AT&T Isdn National Isdn Type Manufacturer PRI Switch Type settingPRI Switch Type Channel HuntingRS366 Dialling Leased Line Data Triggered Manual RS449/V35 CompatibleCall control #008 8B call Bonding #003 #006 6B call Bonding #0029600 Dataport configurationDataport NoneModem mode Data modeControl mode Dataport 1 supports 4 different modes Control Modem 120Restore defaults IP-address TCP/IP SettingsIP-assignment IP-subnet maskWWW-interface What is neededEthernet Functionality Ethernet Vision 5000 Videoconferencing SystemVision 5000 Videoconferencing System Ethernet How is it done Peripheral Equipment Peripherals Vision 5000 Videoconferencing SystemVideo Inputs InterfacesVision 5000 Videoconferencing System Peripherals Video OutputsDual Monitor optional Natural Audio module optional AudioScience module optionalPlease contact your dealer for further information Multiple controllable cameras optional Tracker optionalDocument camera Video Cassette Recorder VCR VCR PlaybackVCR Recording Telephone Add-On Extra camerasOther PC applications PC applicationsVGA to PAL converter VGA PAL/NTSC converterAdditional microphones Appendices Appendix Vision 5000 Videoconferencing SystemUsing Telesync TS-256 SW56/ISDN adapter Vision 5000 Videoconferencing System AppendixConfiguration of Vision VisionINC DSU Configuration ofAdtran T1 ESF Csuace Appendix 3 Connecting Vision 5000 to PRI/T1Using CSU adapter Making a callPower Appendix 4 LED indicationSymbols IndexIndex Vision 5000 Videoconferencing System Vision 5000 Videoconferencing System Index ImuxIndex Vision 5000 Videoconferencing System