TANDBERG 5000 If an output is ‘Off’, no audio will be sent to that output, Level Settings Outputs

Page 55

VISION 5000 Videoconferencing System

Advanced use

Audio Outputs

============= Outputs =============

Out1:Off On

Out2(AUX): Off On

Out3(VCR): Off On Level Settings

Previous Menu

Audio out 1 is intended for connection to Tandberg Natural Audio module, televisions or audio amplifiers with loudspeakers.

Audio out 2 is intended for connection to audio recording equipment or to a telephone add-on hybrid. The signal is a mix of audio from both the remote and local side (not from Audio in 5).

Audio out 3 is intended for connection to a VCR or other recording equipment. The signal is a mix of audio from remote side and local side (not from Audio in 6).

NOTE

Never connect audio out 2 or audio out 3 to a loudspeaker placed in the same room as the microphones connected to the system. Doing this will cause “howling” and possible damage to the speaker system.

If an output is ‘Off’, no audio will be sent to that output.

Level Settings - Outputs

========= Level Settings =========

Out1:	—— +13.5dB
Out2(AUX):	——	+13.5dB
Out3(VCR):	——	+13.5dB
Previous Menu

Adjust the audio output levels according to the parameters of the external audio equipment connected. These levels should be adjusted when installing new audio equipment only. The default settings are correct for the Tandberg Natural Audio module and for most consumer electronics devices (televisions, CD-players, VCRs, etc.).

The audio output levels specify the maximum level of the output.The audio outputs are adjustable in steps of 1.5 dB from 0 dB to 22.5 dB.

The volume control on the remote control will control the level of output 1 (the speaker output). The volume control will have no effect on output 2 and 3.

55

Image 55

Contents N D B E R G Vision 5000 Videoconferencing System Lysaker, Norway, Tel +47 67 125 125, Fax +47 67 125 Environmental IssuesVision 5000 Videoconferencing System Operator Safety Summary Contents Appendices Index Vision 5000 Videoconferencing System Advanced useEthernet Functionality Peripheral EquipmentIntroduction How to use this guideMain menu Menu structureVision 5000 on-screen menu structure is shown below Right keys to move through the menu structureAt a glance the Vision 5000 system Vision 5000 videoconferencing systemMonitors Vision 5000 Videoconferencing System CameraCodec Vision 5000 Videoconferencing System Cart Remote controlTandberg Natural Audio module optional on some systems Vision 5000 Videoconferencing System Table microphoneTandberg AudioScience module optional This product complies with directives 89/366/EEC 93/261/EEC InstallationPrecautions Vision 5000 Videoconferencing System InstallationCamera Table Microphone Remote Control Batteries Installation Vision 5000 Videoconferencing SystemUnpacking Connecting to the Switched 56 network Connecting cablesIsdn cables using BRI interface Isdn cable using the PRI/T1 interfacePress OK to exit menu Power on monitorExample 29 monitor not USA Example 33 monitor not USAPress p+s/tp- to select Special FUNCTIONS, then press OK Power on codecTo highlight Switch on with, select AV with + keys Example monitor USAExternal Network configuration ConfigurationISDN-BRI configuration ISDN-PRI/T1 configurationIris control and lighting Environmental considerationsBackground Brightness control Loudspeaker volumeDo not place the camera facing a doorway Seating Area Table LightingVision Vision 5000 Videoconferencing System Getting started Getting startedSystem start-up On-screen helpGetting started Vision 5000 Videoconferencing System BasicsTo confirm the selection press OK Making a call Making and ending callsVideo call Prefix Call Type Restricted callTelephone call SoftMux only Special call prefixesTo answer a call, press Last number redial/using the call directoryIs switched off. See ‘Utilities’ Correcting keying mistakesGeneral use Vision 5000 Videoconferencing System Adjusting volumeGeneral use View outgoing videoMoving the picture-in-picture PIP Microphone on/offControlling the Main Camera To manually focus the Main Camera, use the Focus keys Camera TrackingHighlighter bar to a source and press OK Enable/Disable Camera TrackingSelecting video sources Selecting audio sourcesSelecting presets PresetsStoring presets Sending a still image Sending/receiving graphicsRequesting a still image Source and 0 to view the still image Receiving a still imageFar end camera control Fecc Overview Advanced useGeneral Advanced use Vision 5000 Videoconferencing SystemMenu structure Main menuAll submenus are explained below Audio Call qualityVideo Motion Video ModeAudio QualityStatus Format ResolutionLow resolution video 176 x 144 pixels ChannelsAlphabetic Sort Edit directoryKey to delete the last character Add New EntryBoth numbers should be specified 2x64 or 2x56 calls Store Last Number Far end camera control UtilitiesAutoanswer Do not disturbSystem Name Presentation SettingsThis menu allows setup of still-image/graphics transfer MCU status lineTest subsystem Power up and system infoView current settings You can test the different subsystems of the VisionCall status BRI Status BRI Status PRI CommentsCall status PRI Cause codes Most common cause codes for Isdn areRequest floor MCU servicesRelease chair Terminal IDChair control Take chairAllows the chairman to terminate the conference altogether Allows the chairman to release the floorAudio Inputs Audio setupLevel Settings Inputs Mix ModeMic1 +3.0dB If an output is ‘Off’, no audio will be sent to that output Level Settings OutputsEcho Control Noise ReductionTips for improving the echo canceller performance Restore Audio Defaults Alert Tones & VolumeAlert Speaker Video input Camera Track ModeEnter a video source name Backlight Camera adjustmentsKeys on the remote control FocusWhitebalance Vision 5000 Videoconferencing System Advanced use BrightnessVideo output Network configuration Terminal settingsISDN-BRI ISDN-PRI/T1 External Ntsc version is shown below Isdn switch typeEtsi Euro Isdn Number2 Number Line SetupSubaddress Advanced Isdn settingsDownspeed Default Call TypeMSN Multi Subscriber Number Parallel dialMax Channels NumberCable Length 1&2 Channel Hunting Type Manufacturer PRI Switch Type settingPRI Switch Type AT&T Isdn National IsdnRS449/V35 Compatible RS366 Dialling Leased Line Data Triggered ManualCall control #006 6B call Bonding #002 #008 8B call Bonding #003None Dataport configurationDataport 9600Dataport 1 supports 4 different modes Control Modem 120 Data modeControl mode Modem modeRestore defaults IP-subnet mask TCP/IP SettingsIP-assignment IP-addressEthernet Vision 5000 Videoconferencing System What is neededEthernet Functionality WWW-interfaceVision 5000 Videoconferencing System Ethernet How is it done Peripherals Vision 5000 Videoconferencing System Peripheral EquipmentVideo Outputs InterfacesVision 5000 Videoconferencing System Peripherals Video InputsDual Monitor optional AudioScience module optional Natural Audio module optionalPlease contact your dealer for further information Tracker optional Multiple controllable cameras optionalDocument camera VCR Playback Video Cassette Recorder VCRVCR Recording Extra cameras Telephone Add-OnVGA PAL/NTSC converter PC applicationsVGA to PAL converter Other PC applicationsAdditional microphones Appendix Vision 5000 Videoconferencing System AppendicesVision 5000 Videoconferencing System Appendix Using Telesync TS-256 SW56/ISDN adapterVision Configuration of VisionINC DSU Making a call Appendix 3 Connecting Vision 5000 to PRI/T1Using CSU adapter Configuration ofAdtran T1 ESF CsuaceAppendix 4 LED indication PowerIndex SymbolsIndex Vision 5000 Videoconferencing System Imux Vision 5000 Videoconferencing System IndexIndex Vision 5000 Videoconferencing System