TANDBERG user manual Appendices, Appendix Vision 5000 Videoconferencing System

Page 88

Appendix 1

VISION 5000 Videoconferencing System

Appendices

Appendix 1: Connecting Vision 5000 to ISDN using NT1 network adapters

Connecting

Connect the first ISDN cable from ISDN 1 on the codec to the S-interface on your first NT1 network adapter. Connect the second, third and fourth ISDN cable to the appropriate NT1 network adapters.

Wall

U-interface

NT1		NT- 384 (NT-1 triple)
NT1
U	S/T	S/T-interface
		1
NT1		2	ISDN
U	S/T	3
		4
NT1
U	S/T
		Vision 5000
NT1
U	S/T

Connect the U-interface of your NT1 adapter to the line provided from your network provider.

For convenience the NT1 adapters could be placed inside the cart. If needed, use the shorter ISDN cable (RJ45 connectors) delivered with the NT1 between the codec and the NT1 and the longer ISDN cable between the NT1 and the connector (RJ45) at the wall socket.

Configuring

The configuration of the codec is performed in the same manner as described in ISDN BRI Settings.

The NT1 should be powered up and you should check that the network is active. Please check your NT1 User Manual.

88

Image 88

Contents N D B E R G Vision 5000 Videoconferencing System Environmental Issues Lysaker, Norway, Tel +47 67 125 125, Fax +47 67 125Vision 5000 Videoconferencing System Operator Safety Summary Contents Vision 5000 Videoconferencing System Advanced use Ethernet FunctionalityPeripheral Equipment Appendices IndexHow to use this guide IntroductionMenu structure Vision 5000 on-screen menu structure is shown belowRight keys to move through the menu structure Main menuVision 5000 videoconferencing system At a glance the Vision 5000 systemMonitors Vision 5000 Videoconferencing System CameraCodec Remote control Vision 5000 Videoconferencing System CartTandberg Natural Audio module optional on some systems Vision 5000 Videoconferencing System Table microphoneTandberg AudioScience module optional Installation PrecautionsVision 5000 Videoconferencing System Installation This product complies with directives 89/366/EEC 93/261/EECCamera Table Microphone Remote Control Batteries Installation Vision 5000 Videoconferencing SystemUnpacking Connecting cables Isdn cables using BRI interfaceIsdn cable using the PRI/T1 interface Connecting to the Switched 56 networkPower on monitor Example 29 monitor not USAExample 33 monitor not USA Press OK to exit menuPower on codec To highlight Switch on with, select AV with + keysExample monitor USA Press p+s/tp- to select Special FUNCTIONS, then press OKConfiguration ISDN-BRI configurationISDN-PRI/T1 configuration External Network configurationIris control and lighting Environmental considerationsBackground Brightness control Loudspeaker volumeDo not place the camera facing a doorway Lighting Seating Area TableVision Getting started System start-upOn-screen help Vision 5000 Videoconferencing System Getting startedGetting started Vision 5000 Videoconferencing System BasicsTo confirm the selection press OK Making a call Making and ending callsVideo call Restricted call Telephone call SoftMux onlySpecial call prefixes Prefix Call TypeLast number redial/using the call directory Is switched off. See ‘Utilities’Correcting keying mistakes To answer a call, pressAdjusting volume General useView outgoing video General use Vision 5000 Videoconferencing SystemMoving the picture-in-picture PIP Microphone on/offControlling the Main Camera Camera Tracking To manually focus the Main Camera, use the Focus keysEnable/Disable Camera Tracking Selecting video sourcesSelecting audio sources Highlighter bar to a source and press OKSelecting presets PresetsStoring presets Sending a still image Sending/receiving graphicsRequesting a still image Receiving a still image Source and 0 to view the still imageFar end camera control Fecc Advanced use GeneralAdvanced use Vision 5000 Videoconferencing System OverviewMenu structure Main menuAll submenus are explained below Audio Call qualityVideo Video Mode AudioQuality MotionResolution Low resolution video 176 x 144 pixelsChannels Status FormatEdit directory Alphabetic SortKey to delete the last character Add New EntryBoth numbers should be specified 2x64 or 2x56 calls Store Last Number Utilities AutoanswerDo not disturb Far end camera controlPresentation Settings This menu allows setup of still-image/graphics transferMCU status line System NamePower up and system info View current settingsYou can test the different subsystems of the Vision Test subsystemStatus BRI Status PRI Comments Call status BRICall status PRI Most common cause codes for Isdn are Cause codesMCU services Request floorTerminal ID Chair controlTake chair Release chairAllows the chairman to release the floor Allows the chairman to terminate the conference altogetherAudio setup Audio InputsLevel Settings Inputs Mix ModeMic1 +3.0dB Level Settings Outputs If an output is ‘Off’, no audio will be sent to that outputNoise Reduction Echo ControlTips for improving the echo canceller performance Restore Audio Defaults Alert Tones & VolumeAlert Speaker Video input Camera Track ModeEnter a video source name Camera adjustments Keys on the remote controlFocus BacklightVision 5000 Videoconferencing System Advanced use Brightness WhitebalanceVideo output Network configuration Terminal settingsISDN-BRI ISDN-PRI/T1 External Ntsc version is shown below Isdn switch typeEtsi Euro Isdn Number Line Setup Number2Advanced Isdn settings SubaddressDefault Call Type MSN Multi Subscriber NumberParallel dial DownspeedMax Channels NumberCable Length 1&2 Type Manufacturer PRI Switch Type setting PRI Switch TypeAT&T Isdn National Isdn Channel HuntingRS449/V35 Compatible RS366 Dialling Leased Line Data Triggered ManualCall control #008 8B call Bonding #003 #006 6B call Bonding #002Dataport configuration Dataport9600 NoneData mode Control modeModem mode Dataport 1 supports 4 different modes Control Modem 120Restore defaults TCP/IP Settings IP-assignmentIP-address IP-subnet maskWhat is needed Ethernet FunctionalityWWW-interface Ethernet Vision 5000 Videoconferencing SystemVision 5000 Videoconferencing System Ethernet How is it done Peripheral Equipment Peripherals Vision 5000 Videoconferencing SystemInterfaces Vision 5000 Videoconferencing System PeripheralsVideo Inputs Video OutputsDual Monitor optional AudioScience module optional Natural Audio module optionalPlease contact your dealer for further information Multiple controllable cameras optional Tracker optionalDocument camera VCR Playback Video Cassette Recorder VCRVCR Recording Telephone Add-On Extra camerasPC applications VGA to PAL converterOther PC applications VGA PAL/NTSC converterAdditional microphones Appendices Appendix Vision 5000 Videoconferencing SystemUsing Telesync TS-256 SW56/ISDN adapter Vision 5000 Videoconferencing System AppendixConfiguration of Vision VisionINC DSU Appendix 3 Connecting Vision 5000 to PRI/T1 Using CSU adapterConfiguration ofAdtran T1 ESF Csuace Making a callPower Appendix 4 LED indicationIndex SymbolsIndex Vision 5000 Videoconferencing System Vision 5000 Videoconferencing System Index ImuxIndex Vision 5000 Videoconferencing System