Sharp PG-F255W quick start Upper side, Control

Page 21

4.Adjust the projected image with the Setup Guide

1After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. See page 45.)

2Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.

3After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup Guide.

_PP. 27, 28

5. Correct trapezoidal distortion

Correcting trapezoidal distortion using Keystone Correction.

On the projector

Shrinks

Shrinks

upper side.

lower side.

 

 

 

 

 

 

On the remote control

_P. 29

6. Select the INPUT mode

Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.

On the

On the remote

INPUT list

On-screen display (RGB)

projector

control

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

COMPUTER

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPUTER

 

 

RGB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1024 768

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DDVI-D Computer

DDVI-D Video

When you press INPUT on the projector, the INPUT list appears. Press '/" to switch the INPUT mode.

_P. 30

7.Turn the computer on

8.Turn the power off

Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confirmation message is displayed to put the projector into standby mode.

On the

On-screen display

On the remote

projector

control

_P. 26

Quick Start

17

Image 21
Contents PG-F255W Model No Serial No If YOU have ANY DOUBT, Consult a Qualified Electrician This Apparatus Must be EarthedPage A. only IntroductionENGLISHOnly InformationFor Future Reference Maintenance Troubleshooting IndexContents Reference Accessories CleaningPower Sources Power-Cord ProtectionReplacement Parts Damage Requiring ServiceSafety Check OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents See ÒRegarding the LampÓ onTemperature monitor function Using the projector in other countriesIf the projector starts to overheat due to setup Other connected equipmentFor Windows Setup ManualOptional accessories AccessoriesProjector Part Names and FunctionsRear View Audio 1 input terminalComputer UP/PAGE COMPUTER, DVICLICK/EFFECT ButtonUsable Range Inserting the BatteriesPull down the tab on the cover and remove the cover Towards the direction of the arrowSetup and Projection Quick StartHeight Control Upper sideSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupExample 1610 Signal Input Normal Mode Picture Size Projection PRJ ModeProjection DistanceScreen Size and Projection Distance Signal Input Normal ModeYou may need other cables or connectors not listed below Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment Audio OUT Controlling the Projector by a Computer Connecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket To AC outlet Power cord supplied Turning the Projector on Turning the Projector On/OffAdjusting the Projected Image Adjusting the Focus About the Setup GuideAdjusting the Picture Size Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightHeight Adjust lever Make small adjustments Rear adjustment footPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Adjusting the Volume Switching the Input ModeCOMPUTER, DVI VIDEO, Video Buttons AV Mute buttonResize Mode Press ResizeResize About Copyrights Displaying and Setting the Break Timer Operating with the Remote ControlUsing the Spot Function Switching the Eco+Quiet ModeSelecting the Picture Mode Auto Sync Auto Sync AdjustmentFreezing a Moving Image Displaying an Enlarged Portion of an ImageWhen moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu Help menu n Items you can set with the Help menuMenu Selections Adjustments Using the Menu ScreenPress Qor Oand select Picture to adjust Example Adjusting ÒBrightÓImage while watching it To adjust the projected1Selecting the Picture Mode Picture Adjustment Picture MenuMenu operation n PAGE1 PAGE23Adjusting the Color Temperature 2Adjusting the Image4Adjusting the Colors Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓLamp Setting ProgressiveReducing Image Noise DNR Setting the Resize Mode Adjusting the Projected Image SCR ADJ MenuAdjusting the Image Position Keystone Correction Setting the On-screen Display5Selecting the Background Image 6Selecting the Setup GuideReversing/Inverting Projected Images 8Selecting the On-screen Display Language2Auto Power Off Function 1Auto Sync Auto Sync Adjustment4STANDBY Mode 5Setting the Confirmation Sound System SoundAudio Input Fan Mode SettingSystem Lock Function This function changes the fan rotation speedEnter the same keycode in Re Checking the Lamp Life StatusConfirm Locking the Operation Buttons1Setting a Password 3TCP/IP Setting 2DHCP Client SettingEnter IP Address using P, R, Q O, then press Enter 4Confirming the Projector InformationTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Storing the Projector How to Use the Storage CaseComputer Computer Compatibility Chart21-25 Troubleshooting52, 53 For Sharp Assistance Specifications Dimensions Index