Sharp PG-F255W quick start Removing and Installing the Lamp Unit, Disconnect the power cord

Page 60

Regarding the Lamp (Continued)

Removing and Installing the Lamp Unit

Warning!

¥Do not remove the lamp unit from the projec- tor right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-F212LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1Press STANDBY/ON on the projec- tor or STANDBY on the remote control to put the projector into standby mode.

•Wait until the cooling fan stops.

2Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

1

2

56

Image 60

Contents PG-F255W Model No Serial No This Apparatus Must be Earthed If YOU have ANY DOUBT, Consult a Qualified ElectricianPage IntroductionENGLISH A. onlyInformation OnlyMaintenance Troubleshooting Index For Future ReferenceContents Reference Cleaning AccessoriesPower Sources Power-Cord ProtectionDamage Requiring Service Replacement PartsSafety Check OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents See ÒRegarding the LampÓ onUsing the projector in other countries Temperature monitor functionIf the projector starts to overheat due to setup Other connected equipmentSetup Manual For WindowsAccessories Optional accessoriesPart Names and Functions ProjectorRear View Audio 1 input terminalComputer COMPUTER, DVI UP/PAGECLICK/EFFECT ButtonInserting the Batteries Usable RangePull down the tab on the cover and remove the cover Towards the direction of the arrowSetup and Projection Quick StartHeight Upper side ControlSetting up the Projector Setting up the ProjectorStandard Setup Front Projection Ceiling-mount SetupProjection PRJ Mode Example 1610 Signal Input Normal Mode Picture SizeProjection DistanceSignal Input Normal Mode Screen Size and Projection DistanceConnecting the Projector to Other Equipment You may need other cables or connectors not listed belowConnecting the Projector to Other Equipment Audio OUT Controlling the Projector by a Computer Connecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket To AC outlet Power cord supplied Turning the Projector On/Off Turning the Projector onAbout the Setup Guide Adjusting the Projected Image Adjusting the FocusAdjusting the Picture Size Image ProjectionAdjusting the Height Use the rear adjustment foot to make the projector levelHeight Adjust lever Make small adjustments Rear adjustment footPress Keystone to enter the Keystone Correction mode Press P/Q or O/R to adjust Keystone CorrectionCorrecting Trapezoidal Distortion Switching the Input Mode Adjusting the VolumeCOMPUTER, DVI VIDEO, Video Buttons AV Mute buttonResize Mode Press ResizeResize About Copyrights Operating with the Remote Control Displaying and Setting the Break TimerUsing the Spot Function Switching the Eco+Quiet ModeAuto Sync Auto Sync Adjustment Selecting the Picture ModeFreezing a Moving Image Displaying an Enlarged Portion of an ImageUsing the Remote Control as the Wireless Computer Mouse When moving the cursorWhen left-clicking When right-clickingMenu Items Following shows the items that can be set in the projectorScreen adjustment SCR-ADJ menu Items you can set with the Help menu Help menu nUsing the Menu Screen Menu Selections AdjustmentsPress Qor Oand select Picture to adjust Example Adjusting ÒBrightÓTo adjust the projected Image while watching itPicture Adjustment Picture Menu 1Selecting the Picture ModeMenu operation n PAGE1 PAGE22Adjusting the Image 3Adjusting the Color Temperature4Adjusting the Colors Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓLamp Setting ProgressiveReducing Image Noise DNR Adjusting the Projected Image SCR ADJ Menu Setting the Resize ModeAdjusting the Image Position Keystone Correction Setting the On-screen Display6Selecting the Setup Guide 5Selecting the Background ImageReversing/Inverting Projected Images 8Selecting the On-screen Display Language1Auto Sync Auto Sync Adjustment 2Auto Power Off Function4STANDBY Mode 5Setting the Confirmation Sound System SoundFan Mode Setting Audio InputSystem Lock Function This function changes the fan rotation speedChecking the Lamp Life Status Enter the same keycode in ReConfirm Locking the Operation Buttons1Setting a Password 2DHCP Client Setting 3TCP/IP SettingEnter IP Address using P, R, Q O, then press Enter 4Confirming the Projector InformationTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Maintenance Cleaning the projectorMaintenance Indicators Temperature warning indicator Lamp indicator Power indicatorPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer How to Use the Storage Case Storing the ProjectorComputer Compatibility Chart ComputerTroubleshooting 21-2552, 53 For Sharp Assistance Specifications Dimensions Index