Troubleshooting
| Problem | Check | Page | ||
|
|
| • Projector power cord is not plugged into the wall outlet. | 25 | |
|
|
| • Power to the external connected devices is off. | – | |
|
|
| • The selected input mode is wrong. | 30 | |
|
|
| • Cables are incorrectly connected to the projector. |
| |
|
|
| • Remote control battery has run out. | 15 | |
|
|
| • External output has not been set when connecting notebook computer. | 21 | |
No picture and no sound | |||||
• The lamp unit cover is not installed correctly. | 56, 57 | ||||
or projector does not | • If the connected DVI digital equipment is turned on before the | 21 | |||
| start. | input mode is selected on the projector, the image may not be |
| ||
|
|
| projected properly or may not be displayed at all. Ensure that the |
| |
|
|
| appropriate input mode has been selected on the projector before you |
| |
|
|
| turn on the connected equipment. |
| |
|
|
| • Cables are incorrectly connected to the projector. | ||
|
|
| • “Bright” is set to minimum position. | 42 | |
|
|
| • Depending on the computer you are using, an image may not be | – | |
|
|
| projected unless the signal output setting of the computer is |
| |
|
|
| switched to the external output. Refer to the computer’s operation |
| |
|
|
| manual for how to switch its signal output settings. |
| |
Sound is heard but no |
|
| |||
| picture appears |
|
| ||
| (or picture is dark). |
|
| ||
|
|
|
|
| |
|
|
| • Image adjustments are incorrectly set. | 42 | |
|
|
| • Make adjustments of “Color” and “Tint” in “Picture Mode” and lower |
| |
|
|
| the “BrilliantColorTM” value. |
| |
|
|
| (Video Input only) |
| |
|
|
| • Video input system is incorrectly set. | 51 | |
|
|
|
|
| |
Color is faded or poor. |
|
| |||
|
|
|
|
| |
|
|
| • Adjust the focus. | 27 | |
|
|
| • The projection distance exceeds the focus range. | 20 | |
|
|
| • There is fog on the lens. If the projector is carried from a cold room into a | – | |
|
|
| warm room, or if it is suddenly heated, condensation may form on the |
| |
|
|
| surface of the lens and the image will become blurred. Set up the |
| |
|
|
| projector at least one hour before it is to be used. If condensation should |
| |
|
|
| form, remove the power cord from the wall outlet and wait for it to clear. |
| |
| Picture is blurred; |
| |||
| (Computer Input only) |
| |||
| noise appears. |
| |||
| • Perform Synchronization Adjustments (“Clock” and “Phase” | 51 | |||
|
|
| |||
|
|
| Adjustment) |
| |
|
|
| • Noise may appear depending on the computer. | – | |
|
|
| • Cables are incorrectly connected to the projector. | ||
|
|
|
|
| |
|
|
| • Volume is set to minimum. | 30 | |
|
|
| • When the projector is connected to an external device and the |
| |
|
|
| volume is set to minimum, the sound is not output even if you turn up |
| |
|
|
| the volume of the external device. |
| |
|
|
|
|
| |
Picture appears but no |
|
| |||
• “Speaker” is set to “Off”. | 46 | ||||
| sound is heard. |
|
| ||
|
|
|
|
| |
| Data image is not | • Select “Data image is not centered” in the “Help” menu and make the | 51 | ||
| centered. | necessary adjustments. |
| ||
|
|
| • Depending on the computer you are using, the output resolution | – | |
|
|
| signal may be different from the one you have set. For details, refer to |
| |
|
|
| the operation manual of the computer. |
| |
|
|
|
|
|
60